35471 Datasheet 35472, 35479, 35471 | P1-P3

3651 Walnut Avenue, Chino, CA 91710

Phone: (909) 627-2453 • Web Site: MendaPump.com

Employee Owned

Series II Fume Extraction System

TECHNICAL BULLETIN TB-4015

Powerful, Portable Fume Extraction

The MENDA Series II Fume Extraction System is a two-arm ltration system that

combines powerful fan performance with ecient ltration. The compact design and easy set-up

makes it truly portable.

Depending on the application, three lter congurations are oered: The standard item (35470)

comes with a 95% ecient Non-HEPA ltration for solder fumes. You also have the option of

purchasing a HEPA lter (35472) or a Deep Bed Gas Filter (35473) for the removal of gases

from solvents, conformal coating, etc.

The air inlet ports allow the connection of 50 mm (2") or 63 mm (2.5") diameter exhaust arms.

Inspection

Item Description

35470 Series II Fume Extractor,w/

Non-HEPA Filter

35471 Pre-Filter (5PK), for use with

(HEPA Filter, Gas Filter Only)

35472 Main Filter, HEPA 99.97% / Carbon

35473 Deep Bed Gas Filter 99.97%

35474 Main Filter, Non HEPA 95%

35475 2.5' Arm w/6' Hose & Bracket

35476 Arm w/Bracket, Clamps

35477 Flex Exhaust Arm 2.5'

35478 Flex Exhaust Arm 5'

35479 Table Bracket, Clamps

35480 Connect Hose, 6'

35481 Connect Hose, 12'

35482 Remote SW, Series II

Items included with model 35470:

• 1 Unit with 35474 lter installed

• 1 Remote Start/Stop Button (35482)

• 1 Power Cord, 120V US Plug

• 2 Flex Exhaust Arms 5' (35478)

35470

TB-4015 July 2016 Page 1 of 5

3651 Walnut Avenue, Chino, CA 91710

Phone: (909) 627-2453 • Web Site: MendaPump.com

Employee Owned

TB-4015 Page 2 of 5

Installation

Extractor Installation Procedure

Remove Fume Extractor from the shipping carton and inspect for any damages. Make sure

you have access to the unit for lter maintenance.

Connect the power cord into the outlet on the side of the system. Plug the power cord into a

grounded wall socket.

Connect the arms/hose to the inlet on the base of the fume extractor.

To power up system, depress the power switch, located on the bottom right of the unit. The

operator can expect a delay of a few seconds before hearing the motor running. This is due to

the built-in motor “Soft-start” feature.

If utilized, connect the supplied remote Start/Stop switch to the system and site the switch

in a convenient position on the workbench. We recommend that this switch be used for your

convenience.

Position the extraction arms to optimize fume capture.

Follow maintenance procedures on next page.

Caution

To provide protection against the risk of electrical shock, connect to properly grounded outlets

only.

Features

• Ecient motor with “soft-start” feature

• Optional, remote Start/Stop switch

• Audible alarm to indicate blocked lters

• Low noise level <55 dba

• High suction force and airow

• Compact and portable

• Standard Filter Eciency at 95% (35474)

• Connects to 50mm (2") or 63mm(2.5") hoses or exhaust arms

• ESD safe housing

• Optional HEPA Filter Available (35472)

• Optional Gas Filter Available (35473)

3651 Walnut Avenue, Chino, CA 91710

Phone: (909) 627-2453 • Web Site: MendaPump.com

Employee Owned

TB-4015 Page 3 of 5

Maintenance

General

User maintenance is limited to cleaning the unit and replacing the lters with new. Only

MENDA is authorized to carry out component testing and replacement. Unauthorized work or

the use of unauthorized replacement lters may result in a potentially dangerous situation and/

or damage to the extractor unit, and will invalidate the manufacturer’s warranty.

Cleaning Unit

To clean, use a light wipe with a gentle cleaner to prevent build up of particulate and ux

residue. Be sure the unit is turned o while cleaning.

The cooling inlets and outlets should be cleaned once a year to prevent build up of dust and

overheating of which are on each side of the unit.

Replacing Filters

1. Turn unit o and disconnect the power cord.

2. Unlatch both lter cover catches and remove the lter cover. (see below)

Place Filter inside

the Alignment Pins

Step 2:

Unhook

Latch

Step 1:

Pull & Lift

Latch

Filter

On/O

Switch

Latch

P1-P3 P4-P5

35471

Mfr. #:

Buy 35471

Manufacturer:

Menda

Description:

Soldering Workstation Equipment PRE-FILTERS, (PACK OF 5) SERIES II

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

35471

35471

Products related to this Datasheet