© Semiconductor Components Industries, LLC, 2016
October, 2016 − Rev. 5
1 Publication Order Number:
CAT9532/D
CAT9532
16-bit Programmable LED
Dimmer with I
2
C Interface
Description
The CAT9532 is a CMOS device that provides 16−bit parallel
input/output port expander optimized for LED dimming control. The
CAT9532 outputs can drive directly 16 LEDs in parallel. Each
individual LED may be turned ON, OFF, or blinking at one of two
programmable rates. The device provides a simple solution for
dimming LEDs in 256 brightness steps for backlight and color mixing
applications. The CAT9532 is suitable in I
2
C and SMBus compatible
applications where it is necessary to limit the bus traffic or free−up the
bus masters timer.
The CAT9532 contains an internal oscillator and two PWM signals
that drive the LED outputs. The user can program the period and duty
cycle for each individual PWM signal. After the initial set−up
command to program the Blink Rate 1 and Blink Rate 2 (frequency
and duty cycle), only one command from the bus master is required to
turn each individual open drain output ON, OFF, or cycle at Blink
Rate 1 or Blink Rate 2. Each open drain LED output can provide a
maximum output current of 25 mA. The total current sunk by all I/Os
must not exceed 400 mA.
Features
16 LED Drivers with Dimming Control
256 Brightness Steps
16 Open Drain Outputs Drive 25 mA Each
2 Selectable Programmable Blink Rates:
– Frequency: 0.593 Hz to 152 Hz
– Duty Cycle: 0% to 99.6%
I/Os can be Used as GPIOs
400 kHz I
2
C Bus Compatible
2.3 V to 5.5 V Operation
5 V Tolerant I/Os
Active Low Reset Input
24−Lead TSSOP and 24−pad TQFN (4 x 4 mm) Packages
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
Backlighting
RGB Color Mixing
Sensors Control
Power Switches, Push−buttons
Alarm Systems
www.onsemi.com
TSSOP−24
Y SUFFIX
CASE 948AR
TQFN−24
HV6 SUFFIX
CASE 510AG
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
ORDERING INFORMATION
CAT9532
www.onsemi.com
2
MARKING DIAGRAMS
A = Assembly Location
B = Product Revision (Fixed as “B”)
CAT9532Y = Device Code
I = Temperature Range
3 = Matte-Tin Lead Finish
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
XXX = Last Three Digits of
= Assembly Lot Number
LAAC = Device Code
A = Assembly Location
XXX = Last Three Digits of
= Assembly Lot Number
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
CC = Country Code
= TH = Thailand
= MY = Malaysia
AB
CAT9532YI
3YMXXX
LAAC
AXXX
YMCC
TQFN (HV6)
TSSOP (Y)
Figure 1. Pin Configurations
RESET
LED15
LED14
LED13
LED12
LED11
LED0
LED1
LED2
LED3
LED4
LED5
A2
A1
A0
V
CC
SDA
SCL
LED6
LED7
V
SS
LED8
LED9
LED10
TSSOP (Y)
(Top View)
TQFN (HV6)
(Top View)
RESET
LED15
LED14
LED13
LED12
LED11
LED10
LED9
LED8
SCL
SDA
V
CC
1
LED7
V
SS
LED5
LED6
LED3
LED4
LED1
LED2
A2
LED0
A0
A1
1
Figure 2. Typical Application Circuit
CAT9532
GPIOs
Master
V
SS
A0
A1
A2
RS0 RS1 RS11
5 V
LED11
LED1
LED0
V
CC
LED12
LED15
SDA
5 V
SCL
RESET
I
2
C/SMBus
SDA
SCL
RESET
3 x 10 kW
CAT9532
www.onsemi.com
3
Table 1. PIN DESCRIPTION
TSSOP TQFN Pin Name Function
1 22 A0 Address Input 0
2 23 A1 Address Input 1
3 24 A2 Address Input 2
4−11 1−8 LED0 − LED7 LED Driver Output 0 to 7, I/O Port 0 to 7
12 9 V
SS
Ground
13−20 10−17 LED8 − LED15 LED Driver Output 8 to 15, I/O Port 8 to 15
21 18 RESET Reset Input
22 19 SCL Serial Clock
23 20 SDA Serial Data
24 21 V
CC
Power Supply
SCL
A2 A1 A0
SDA
LEDx
INPUT
FILTERS
POWER ON
RESET
OSCILLATOR
PRESCALER 0
REGISTER
PRESCALER 1
REGISTER
PWM 0
REGISTER
LED SELECT (LSx)
REGISTER
INPUT
REGISTER
BLINK 0
CAT9532
BLINK 1
CONTROL
LOGIC
PWM 1
REGISTER
Note: Only one I/O is shown for clarity
CONTROL
Figure 3. Block Diagram
V
CC
V
SS
RESET
I
2
C BUS
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameters Ratings Units
V
CC
with Respect to Ground −0.3 to +7.0 V
Voltage on Any Pin with Respect to Ground −0.3 to +5.5 V
DC Current on I/Os ±25 mA
Supply Current 400 mA
Package Power Dissipation Capability (T
A
= 25°C) 1.0 W
Junction Temperature +150 °C
Storage Temperature −65 to +150 °C
Lead Soldering Temperature (10 seconds) 300 °C
Operating Ambient Temperature −40 to +85 °C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.

CAT9532HV6I-GT2

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
LED Lighting Drivers I2C/SMBus Expander w/LED Dimming
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet