OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EL7156CNZ

P1-P3P4-P6P7-P9P10-P11
1
FN7280.4
EL7156
High Performance Pin Driver
The EL7156 high performance pin driver with three-state is
suited to many ATE and level-shifting applications. The 3.5A
peak drive capability makes this part an excellent choice
when driving high capacitance loads.
The output pin OUT is connected to input pins VH or VL
respectively, depending on the status of the IN pin. When the
OE pin is active low, the output is placed in the three-state
mode. The isolation of the output FETs from the power
supplies enables VH and VL to be set independently,
enabling level-shifting to be implemented. Related to the
EL7155, the EL7156 adds a lower supply pin VS- and makes
VL an isolated and independent input. This feature adds
applications flexibility and improves switching response due
to the increased enhancement of the output FETs.
This pin driver has improved performance over existing pin
drivers. It is specifically designed to operate at voltages
down to 0V across the switch elements while maintaining
good speed and ON-resistance characteristics.
Available in the 8 Ld SOIC and 8 Ld PDIP packages, the
EL7156 is specified for operation over the full -40°C to
+85°C temperature range.
Features
• Clocking speeds up to 40MHz
• 15ns t
R
/t
F
at 2000pF C
LOAD
• 0.5ns rise and fall times mismatch
• 0.5ns t
ON
-t
OFF
prop delay mismatch
• 3.5pF typical input capacitance
• 3.5A peak drive
• Low ON-resistance of 3.5Ω
• High capacitive drive capability
• Operates from 4.5V to 16.5V
• Pb-free plus anneal available (RoHS compliant)
Applications
• ATE/burn-in testers
• Level shifting
•IGBT drivers
• CCD drivers
Pinout
EL7156
(8 LD PDIP, SOIC)
TOP VIEW
1
2
3
4
8
7
6
5
L
O
G
I
C
VS+
OE
IN
GND
VH
OUT
VL
VS-
Ordering Information
PART NUMBER PART MARKING TAPE & REEL PKG PKG. DWG. #
EL7156CNZ (Note)
(No longer available, recommended replacement: EL7156CSZ)
EL7156CN Z - 8 Ld PDIP* (Pb-free) MDP0031
EL7156CSZ (Note) 7156CSZ - 8 Ld SOIC (Pb-free) MDP0027
EL7156CSZ-T7 (Note) 7156CSZ 7” 8 Ld SOIC (Pb-free) MDP0027
EL7156CSZ-T13 (Note) 7156CSZ 13” 8 Ld SOIC (Pb-free) MDP0027
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
Data Sheet September 1, 2015
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas LLC
Copyright Intersil Americas LLC 2003, 2005, 2007, 2015. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
2
FN7280.4
September 1, 2015
Absolute Maximum Ratings (T
A
= +25°C) Thermal Information
Supply Voltage (V
S
+ to V
S
-) . . . . . . . . . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . V
S
- -0.3V, V
S
+0.3V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . 200mA
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications V
S
+ = +15V, V
H
= +15V, V
L
= 0V, V
S
- = 0V, T
A
= +25°C, unless otherwise specified.
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
INPUT
V
IH
Logic ‘1’ Input Voltage 2.4 V
I
IH
Logic ‘1’ Input Current V
IH
= V
S
+0.110µA
V
IL
Logic ‘0’ Input Voltage 0.8 V
I
IL
Logic ‘0’ Input Current V
IL
= 0V 0.1 10 µA
C
IN
Input Capacitance 3.5 pF
R
IN
Input Resistance 50 MΩ
OUTPUT
R
OVH
ON-Resistance V
H
to OUT I
OUT
= -200 mA 2.7 4.5 Ω
R
OVL
ON-Resistance V
L
to OUT I
OUT
= +200 mA 3.5 5.5 Ω
I
OUT
Output Leakage Current OE = 0V, OUT = V
H
/V
L
0.1 10 µA
I
PK
Peak Output Current
(linear resistive operation)
Source 3.5 A
Sink 3.5 A
I
DC
Continuous Output Current Source/Sink 200 mA
POWER SUPPLY
I
S
Power Supply Current Inputs = V
S
+1.33mA
I
VH
Off Leakage at V
H
and V
L
V
H
, V
L
= 0V 4 10 µA
SWITCHING CHARACTERISTICS
t
R
Rise Time C
L
= 2000pF 14.5 ns
t
F
Fall Time C
L
= 2000pF 15 ns
t
RFΔ
t
R
, t
F
Mismatch C
L
= 2000pF 0.5 ns
t
d-1
Turn-Off Delay Time C
L
= 2000pF 9.5 ns
t
d-2
Turn-On Delay Time C
L
= 2000pF 10 ns
t
dΔ
t
d-1
-t
d-2
Mismatch C
L
= 2000pF 0.5 ns
t
d-3
Three-state Delay Enable 10 ns
t
d-4
Three-state Delay Disable 10 ns
EL7156
3
FN7280.4
September 1, 2015
Electrical Specifications V
S
+ = +5V, V
H
= +5V, V
L
= -5V, V
S
- = -5V, T
A
= +25°C, unless otherwise specified. (Continued)
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
INPUT
V
IH
Logic ‘1’ Input Voltage 2.0 V
I
IH
Logic ‘1’ Input Current V
IH
= V
S
+0.110µA
V
IL
Logic ‘0’ Input Voltage 0.8 V
I
IL
Logic ‘0’ Input Current V
IL
= 0V 0.1 10 µA
C
IN
Input Capacitance 3.5 pF
R
IN
Input Resistance 50 MΩ
OUTPUT
R
OVH
ON-Resistance V
H
to OUT I
OUT
= -200mA 3.4 5 Ω
R
OVL
ON-Resistance V
L
to OUT I
OUT
= +200mA 4 6 Ω
I
OUT
Output Leakage Current OE = 0V, OUT = V
H
/V
L
0.1 10 µA
I
PK
Peak Output Current
(linear resistive operation)
Source 3.5 A
Sink 3.5 A
I
DC
Continuous Output Current Source/Sink 200 mA
POWER SUPPLY
I
S
Power Supply Current Inputs = V
S
+12.5mA
V
H
Off Leakage at V
H
and V
L
V
H
, V
L
= 0V 4 10 µA
SWITCHING CHARACTERISTICS
t
R
Rise Time C
L
= 2000pF 17 ns
t
F
Fall Time C
L
= 2000pF 17 ns
t
RFΔ
t
R
, t
F
Mismatch C
L
= 2000pF 0 ns
t
d-1
Turn-Off Delay Time C
L
= 2000pF 11.5 ns
t
d-2
Turn-On Delay Time C
L
= 2000pF 12 ns
t
dΔ
t
d-1
-t
d-2
Mismatch C
L
= 2000pF 0.5 ns
t
d-3
Three-state Delay Enable 10 ns
t
d-4
Three-state Delay Disable 10 ns
EL7156
P1-P3P4-P6P7-P9P10-P11

EL7156CNZ

Mfr. #:
Buy EL7156CNZ
Manufacturer:
Renesas / Intersil
Description:
Gate Drivers EL7156CNZ 40 MHZ PIN DRVR W/LVL SHIFTER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet