VS-40TPS...PbF Series, VS-40TPS...-M3 Series
www.vishay.com
Vishay Semiconductors
Revision: 02-Jun-15
2
Document Number: 94388
For technical questions within your region: DiodesAmericas@vishay.com
, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum average on-state current I
T(AV)
T
C
= 79 °C, 180° conduction half sine wave 35
A
Maximum continuous RMS
on-state current as AC switch
I
T(RMS)
55
Maximum peak, one-cycle
non-repetitive surge current
I
TSM
10 ms sine pulse, rated V
RRM
applied
Initial
T
J
= T
J
max.
500
10 ms sine pulse, no voltage reapplied 600
Maximum I
2
t for fusing I
2
t
10 ms sine pulse, rated V
RRM
applied 1250
A
2
s
10 ms sine pulse, no voltage reapplied 1760
Maximum I
2
t for fusing I
2
t t = 0.1 ms to 10 ms, no voltage reapplied 17 600 A
2
s
Low level value of threshold voltage V
T(TO)1
T
J
= 125 °C
1.02
V
High level value of threshold voltage V
T(TO)2
1.23
Low level value of on-state slope resistance r
t1
9.74
m
High level value of on-state slope resistance r
t2
7.50
Maximum peak on-state voltage V
TM
110 A, T
J
= 25 °C 1.85 V
Maximum rate of rise of turned-on current dI/dt T
J
= 25 °C 100 A/μs
Maximum holding current I
H
Anode supply = 6 V, resistive load, initial T
J
= 1 A, I
T
= 25 °C 200
mA
Maximum latching current I
L
Anode supply = 6 V, resistive load, T
J
= 25 °C 300
Maximum reverse and direct leakage current I
RRM/
I
DRM
T
J
= 25 °C
V
R
= Rated V
RRM
/V
DRM
0.5
T
J
= 125 °C 10
Maximum rate of rise of off-state voltage
40TPS12A
dV/dt T
J
= T
J
maximum, linear to 80 % V
DRM
, R
g
- k = 100
500
V/μs
Maximum rate of rise of off-state voltage
40TPS12
1000
TRIGGERING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum peak gate power P
GM
10
W
Maximum average gate power P
G(AV)
2.5
Maximum peak gate current I
GM
2.5 A
Maximum peak negative gate voltage - V
GM
10 V
Maximum required DC gate voltage to trigger V
GT
T
J
= - 40 °C
Anode supply = 6 V
resistive load
4.0
VT
J
= 25 °C 2.5
T
J
= 125 °C 1.7
Maximum required DC gate current to trigger I
GT
T
J
= - 40 °C
Anode supply = 6 V
resistive load
270
mA
T
J
= 25 °C 150
T
J
= 125 °C 80
T
J
= 25 °C, for 40TPS08APbF and 40TPS12APbF 40
Maximum DC gate voltage not to trigger
for 40TPS12
V
GD
T
J
= 125 °C, V
DRM
= Rated value
0.25 V
Maximum DC gate current not to trigger
for 40TPS12
I
GD
6mA
Maximum DC gate voltage not to trigger
for 40TPS12A
V
GD
T
J
= 125 °C, V
DRM
= Rated value
0.15 V
Maximum DC gate current not to trigger
for 40TPS12A
I
GD
1mA
