NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
REVISIONS
REV
DESCRIPTION
DATE
APPV
B SAH
B
10-JUL-12
B.MURPHY
S.HOGAN
10-JUL-12
Updated footprint and dimensions; Added new title block 10-JUL-12
RECOMMENDED CABLE STRIPPING DIMENSIONS
Descripon Material Finish
Body
Socket
Insulaon
Nickel
N/A
Gold
PTFE
O-Ring
Crimp ring
Washer
Rubber
Nickel
Nickel
SI Rubber
Brass
Brass
Nut NickelBrass
Heat Shrink BlackPolyolefin
Brass
Brass
SIDE VIEW
0.354
[9.00]
Ø0.049
[1.24]
Ø0.024
[0.60]
PIN CHUCK
0.2x2x2mm GROOVE
Ø0.020
[0.50]
SOCKET
RECOMMENDED
MOUNTING HOLE
0.234
[6.00]
Ø0.256
[6.50]
HEAT SHRINK
CRIMP RING
0.020
[0.50]
0.065
[1.65]
NUT
1/4-36UNS-2B
THREADS
H0.315
[8.00]
Ø0.402
[10.20]
WASHER
0.055
[1.40]
Ø0.236
[6.00]
Ø0.358
[9.10]
0.276
[7.00]
0.098
[2.50]
0.098
[2.50]
RG-58 Cable
0.276
[7.00]
0.327
[8.30]
0.083
[2.10]
0.417
[10.60]
0.748
(21.00)
FLAT 0.228
[5.80]
Ø0.177
[4.50]
Ø0.236
[6.00]
H0.433
[11.00]
1/4"-36UNS-2A
THREADS
Ø0.287
[7.30]
0.984
[25.00]
4. Solder the socket to the center conductor.
5. Insert the socket, center conductor, and insulation into the body.
6. Wrap the braid around the tail of the body and crimp the ring with
0.213" hex crimp tool (or one labeled for use with RG-58 cable).
CONSMA014-R58 ASSEMBLY INSTRUCTIONS
2. Slip heat shrink and crimp ring onto stripped cable.
3. Insert o-ring into groove in the nut on body.
1. Strip the cable to recommended dimensions.
7. Use heat shrink to cover crimp.
8. Use the nut and washer to secure the connector to a case.
(2.50mm maximum wall thickness)
Ø0.256
[6.50]
0.500
[12.70]
O-RING
SMA FEMALE BULKHEAD MOUNT CABLE
END CRIMP WITH O-RING FOR RG58 CABLE
CONSMA014-R58
