DQ-M (ADQM)
–3–
ASCTB179E 201607-T
DIMENSIONS (mm inch)
NOTES
The CAD data of the products with a CAD Data mark can be downloaded from: http://industrial.panasonic.com/ac/e/
Notes: 1. These are dummy terminals for the strength reinforcement for the M4 screw terminal connection.
Fix or solder these to the PC board in case setting M4 screw.
However, do not use the dummy terminals as wiring to the PC board. In case wiring of the dummy
terminals, the conductor destruction may occur due to the high current.
2. No 3rd terminal on 1 coil latching type.
External dimensions
Note 1)
2 coil latching
type only
This differs with
the part No.
0.8
.031
0.8
.031
7.62
.300
3.6
.142
0.8
.031
0.8
.031
2-4.3 dia.
2-.169 dia.
2-8.7
2-.343
Lot. No.
1.5
.059
(8.9)
(.350)
(2.0)
(.079)
5.08
.200
5.08
.200
1.8
.071
0.4
.016
1.5
.059
0.4
.016
5.8
.228
25.4
1.000
29.5
1.161
40.4
1.591
19.42
.765
20.56
.809
2-9.9
2-.390
29.0
1.142
38.0
1.496
44.0
1.732
34.5
1.358
40.4
1.591
22.86
.700
3.7
.146
17.3
.681
9.25
.364
5.08
.200
0.3
.012
General tolerance: ±0.3 ±.012
PC board pattern (Bottom view)
Tolerance: ±0.1 ±.004
Schematic (Bottom view)
2 coil latching type only
7.62
.300
3-1.5 dia.
3-.059 dia.
4-2.0 dia.
4-.079 dia.
5.08
.200
17.78
.700
25.4
1.000
5.08
.200
5.08
.200
2 coil latching type1 coil latching type
+
-
--
1
5
4
2
6
7
6
7
Reset
coil
Set
coil
+
1
5
4
32
CAD Data
1. For cautions for use, please read
“GENERAL APPLICATION
GUIDELINES”.
2. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%. However,
check it with the actual circuit since the
characteristics may be slightly different.
Also, the power waveform should be
square and we recommend it be at least
0.1 seconds. Please keep continuous
power to the coil to within 10 seconds.
3. Usage, transport and storage
conditions
1) Temperature:
–40 to +70°C –40 to +158°F
2) Humidity: 5 to 75% RH
(Avoid freezing and condensation.)
The humidity range depends on the
temperature. The allowable range are as
shown in the below figure.
3) Air pressure: 86 to 106 kPa
Temperature and humidity range for
operation, transport, and storage
4. Others
Installation of M4 securing screw
Do not apply excessive pressure on the
terminals. This could adversely affect
relay performance. Secure a dummy
terminal designed for reinforcement of
the terminal to the PC board and use a
washer in order to prevent deformation.
Keep the installation torque to within 1.2
and 1.4 N·m (12 to 14 kgf·cm). Also, use
a spring washer to prevent it from
loosening. Do not connect the dummy
terminals designed for reinforcement of
the terminal as wiring to the PC board.
The conductor destruction may occur
according to the amount of current.
5
75
Humidity, %R.H.
070–40
+32 +158–40
Ambient temperature, °C °F
(Avoid
condensation
when used at
temperatures
higher than
0°C
(Avoid icing
when used at
temperatures
lower than
0°C 32°F)
32°F)
Allowable range