OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

2862945

P1-P3P4-P6P7-P9
IB IL 24 DO 8 ...
5558_en_08 PHOENIX CONTACT 7
5 Local diagnostic and status indica-
tors and terminal point assignment
5.1 Local diagnostic and status indicators
Figure 2 Local diagnostic and status indicators
5.2 Function identification
Pink
2 Mbps: white stripe in the vicinity of the D LED
5.3 Terminal point assignment for each connector
Figure 3 Terminal point numbering: individual connec-
tors (A) and connector sets (B)
Des. Color Meaning
D Green Diagnostics
1, 2 Yellow Status indicators for the outputs
1
2
D
D O 8
1
2
1
2
1
2
5 5 5 8 C 0 0 2
A –Using the IB IL 24 DO 8-PAC/SN or
IB
IL 24 DO 8-2MBD-PAC/SN
with the supplied connectors
– Using individual connectors
(IB IL SCN-8 or IB IL SCN-8-CP)
B –Using the IB IL 24 DO 8-PAC or
IB
IL 24 DO 8-2MBD-PAC
with the original connector set
– Using a connector set
(IB IL DI/DO 8-PLSET or
IB IL DI/DO 8-PLSET/CP)
Terminal
point
Assignment
x.1 Signal output (OUT)
x.2 Segment voltage U
S
for 4-wire termination
Measuring points for the supply voltage
x.3 Ground contact (GND)
for 2, 3, and 4-wire termination
x.4 FE connection
for 3 and 4-wire termination
x x xx
5558A010
12
1
2
3
4
1
2
3
4
1.1
1.2
2.1
2.2
1.3
2.3
1.4
2.4
4x
AB
12
1.1
1.2
1.3
1.4
2.1
2.2
2.3
2.4
12
3.1
3.2
3.3
3.4
4.1
4.2
4.3
4.4
12
5.1
5.2
5.3
5.4
6.1
6.2
6.3
6.4
12
7.1
7.2
7.3
7.4
8.1
8.2
8.3
8.4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1.1
1.2
1.3
1.4
8.1
8.3
8.4
8.2
IB IL 24 DO 8 ...
5558_en_08 PHOENIX CONTACT 8
6 Connection example
Figure 4 Typical connection of actuators
A 4-wire termination
B 3-wire termination
The numbers above the module illustration identify the con-
nector slots.
7 Notes on using the terminals within
a safety-related segment circuit
The terminals of the following hardware version and later
(listed below) are approved for use within a safety-related
segment circuit.
Figure 5 Labeling on an Inline terminal
When connecting the actuators observe the as-
signment of the terminal points to the process
data (see
page 9).
1 2
1
2
3
4
1
2
3
4
1 2
1
2
3
4
1
2
3
4
1 2
1
2
3
4
1
2
3
4
1 2
1
2
3
4
1
2
3
4
1
2
D
D O 8
1
2
1
2
1
2
5 5 5 8 2 0 0 4
1
2 3
4
+ 2 4 V
O U T
A
O U T
B
Order No. Order designation Hardware
version
2861289 IB IL 24 DO 8-PAC 05
2862945 IB IL 24 DO 8-PAC/SN 07
2726269 IB IL 24 DO 8 05
2861687 IB IL 24 DO 8-2MBD-PAC 04
2878227 IB IL 24 DO 8-2MBD-PAC/SN 04
2819037 IB IL DO 8-2MBD 04
The hardware version is marked on the side of the
housing of every terminal (1 in
Figure 5).
The instructions in the current documentation for
the safety terminal used and from the
AH EN IL SAFE application note must be ob-
served to ensure that operation of the safety-re-
lated segment circuit is not adversely affected.
The latest documentation can be downloaded at
www.phoenixcontact.net/catalog.
I N T E R B U S
I B I L 2 4 D O 8
O r d e r - N o . : 2 7 2 6 2 6 9
M o d u l e - I D : X X H W / S W 0 5 / -
1
5 5 5 8 A 0 0 8
IB IL 24 DO 8 ...
5558_en_08 9
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00
PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300
www.phoenixcontact.com
8 Programming data/
configuration data
8.1 Local bus (INTERBUS)
8.2 Other bus systems
9 Process data
Assignment of the terminal points to OUT process data
The following table applies to the IB IL 24 DO 8-PAC and
IB
IL 24 DO 8-2MBD-PAC terminals with the original con-
nector set and when using the IB IL DI/DO 8-PLSET and IB
IL DI/DO 8-PLSET/CP connector sets (see also
Figure 3 on
page 7, detail B).
The following table applies to the IB IL 24 DO 8-PAC/SN
and IB
IL 24 DO 8-2MBD-PAC/SN terminals with the origi-
nal connector set and when using the IB IL SCN-8 or IB IL
SCN-8-CP connectors (see also
Figure 3 on page 7,
detail A).
ID code BD
hex
(189
dec
)
Length code 81
hex
Process data channel 8 bits
Input address area 0 bytes
Output address area 1 byte
Parameter channel (PCP) 0 bytes
Register length (bus) 1 byte
For the programming data/configuration data of
other bus systems, please refer to the corre
-
sponding electronic device data sheet (GSD,
EDS).
For the assignment of the illustrated (byte.bit)
view to your INTERBUS control or computer sys
-
tem, please refer to the
DB
GB IBS SYS ADDRESS data sheet.
(Byte.bit)
view
Byte Byte 0
Bit 7 6 5 4 3 2 1 0
Assign-
ment
Slot 4 3 2 1
Terminal
point (signal)
8.1 7.1 6.1 5.1 4.1 3.1 2.1 1.1
Terminal point
(+24 V)
8.2 7.2 6.2 5.2 4.2 3.2 2.2 1.2
Terminal point
(GND)
8.3 7.3 6.3 5.3 4.3 3.3 2.3 1.3
Terminal point
(FE)
8.4 7.4 6.4 5.4 4.4 3.4 2.4 1.4
Status in-
dicator
Slot 4 3 2 1
LED 2 1 2 1 2 1 2 1
(Byte.bit)
view
Byte Byte 0
Bit 7 6 5 4 3 2 1 0
Assign-
ment
Slot 4 3 2 1
Terminal
point (signal)
2.1 1.1 2.1 1.1 2.1 1.1 2.1 1.1
Terminal point
(+24 V)
2.2 1.2 2.2 1.2 2.2 1.2 2.2 1.2
Terminal point
(GND)
2.3 1.3 2.3 1.3 2.3 1.3 2.3 1.3
Terminal point
(FE)
2.4 1.4 2.4 1.4 2.4 1.4 2.4 1.4
Status in-
dicator
Slot 4 3 2 1
LED 2 1 2 1 2 1 2 1
P1-P3P4-P6P7-P9

2862945

Mfr. #:
Buy 2862945
Manufacturer:
Phoenix Contact
Description:
Controllers IB IL 24 DO 8-PAC/SN
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet