3
FN6406.0
December 15, 2006
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Absolute Maximum Ratings (T
A
= +25°C) Operating Conditions
Supply Voltage between V
S
+ and V
S
-. . . . . . . . . . . . . . . . . . . . .12V
Maximum Continuous Output Current per Channel. . . . . . . . . 30mA
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . . V
S
- -0.5V to V
S
+ +0.5V
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Die Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications V
SA
+
= V
A
+
= +5V, V
SA
-
= V
A
-
= -5V, T
A
= +25°C, exposed die plate = -5V, unless otherwise specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
AC PERFORMANCE
BW Bandwidth (See Figure 1) 150 MHz
SR Slew Rate V
IN
= -1V to +1V, V
G
= 0.39, V
C
= 0,
R
L
= 75 + 75Ω
1.5 kV/µs
THD Total Harmonic Distortion 10MHz 2V
P-P
out, V
G
= 1V, X2 gain, V
C
= 0 -50 dBc
DC PERFORMANCE
V(V
OUT
)
OS
Offset Voltage X2 = high, no equalization -110 -15 +110 mV
ΔV
OS
Channel-to-Channel Offset Matching X2 = high, no equalization -140 0 +140 mV
INPUT CHARACTERISTICS
CMIR Common-Mode Input Range -4/+3.5 V
O
NOISE
Output Noise V
G
= 0V, V
C
= 0V, X2 = HIGH, R
LOAD
= 150Ω,
Input 50Ω to GND, 10MHz
-110 dBm
CMRR Common-Mode Rejection Ratio Measured at 10kHz -80 dB
CMRR Common-Mode Rejection Ratio Measured at 10MHz -55 dB
CMBW CM Amplifier Bandwidth 10k || 10pF load 50 MHz
CM
SLEW
CM Slew Rate Measured @ +1V to -1V 100 V/µs
C
INDIFF
Differential Input Capacitance Capacitance V
INP
to V
INM
600 fF
R
INDIFF
Differential Input Resistance Resistance V
INP
to V
INM
1MΩ
C
INCM
CM Input Capacitance Capacitance V
INP
= V
INM
to GND 1.2 pF
R
INCM
CM Input Resistance Resistance V
INP
= V
INM
to GND 1 MΩ
+I
IN
Positive Input Current DC bias @ V
INP
= V
INM
= 0V 1 µA
-I
IN
Negative Input Current DC bias @ V
INP
= V
INM
= 0V 1 µA
V
INDIFF
Differential Input Range V
INP
- V
INM
when slope gain falls to 0.9 2.5 V
OUTPUT CHARACTERISTICS
V(V
OUT
) Output Voltage Swing R
L
= 150Ω ±3.5 V
I(V
OUT
) Output Drive Current R
L
= 10Ω, V
INP
= 1V, V
INM
= 0V, X2 = high,
V
G
= 0.39
50 60 mA
R(V
CM
) CM Output Resistance of
VCM_R/G/B (ISL59913 only)
at 100kHz 30 Ω
Gain Gain V
C
= 0, V
G
= 0.39, X2 = 5, R
L
= 150Ω 0.85 1.0 1.1
ΔGain @ DC Channel-to-Channel Gain Matching V
C
= 0, V
G
= 0.39, X2 = 5, R
L
= 150Ω 38%
ΔGain @
15MHz
Channel-to-Channel Gain Matching V
C
= 0.6, V
G
= 0.39, X2 = 5, R
L
= 150Ω,
Frequency = 15MHz
311%
V(SYNC)
HI
High Level output on V/H
OUT
(ISL59910 only)
V(V
SP
)
- 0.1V
V(V
SP
)
ISL59910, ISL59913
