OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EVP-AWED4A

P1-P3
Light Touch Switches/EVPAW
1 2 345678
Product Code
Type Height
9
Note: Non washable
(
＊
.tset gnirud detarepo eb ton llahs hctiwS : 76PI )1
Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function.
However, IP67 shall be guaranteed under single product state,
then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage.
So, please ask us in advance, if the switch is applied to important usage for water and dust resistant.
■ Specifi cations
■ Features
● External dimensions : 3.0 mm
×
2.0 mm, Height 0.6 mm
● High operability equipped with an actuator(push plate)
● IP67
■ Explanation of Part Numbers(Standard specification only)
3.0 mm×2.0 mm SMD Light Touch Switches
Type:
EVPAW
■ Recommended Applications
● Operationswitchesforportableelectronicequipments
(Mobile phone, Portable audio)
Type Snap action/Push-on type SPST
Electrical
Rating 10 μA 2 V DC to 20 mA 15 V DC (Resistive load)
Contact Resistance 500 mΩ max.
Insulation Resistance 50 MΩ min. (at 100 V DC)
egatloV gni dnats htiW cirtceleiD 250 V AC for 1 minute
Bouncing 10 ms max. (ON, OFF)
Mechanical
Operating Force 1.6 N, 2.4 N, 3.3 N
Travel 1.6 N, 2.4 N : 0.13 mm 3.3 N : 0.15 mm
Endurance Operating Life 1.6 N, 2.4 N : 500,000 cycles min. 3.3 N : 300,000 cycles min.
IP67(
＊
1)
IP6x (Dust resistance) Dust : Talc (Type4) 8h
IPx7 (Water resistance) Immersion dep
th : 1 m 30 min.
Operating Temperature –40 °C to +85 °C
Storage Temperature
–40 °C to +85 °C (Bulk)
–20 °C to +60 °C (Taping)
Minimum Quantity/Packing Unit 10,000 pcs. Embossed Taping (Reel Pack)
Quantity/Carton 50,000 pcs.
industrial.panasonic.com/ac/e/
201 6.11
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB14E 201611-Fd
 
Panasonic Corporation 2016
–1–
D4A
Operating
Force
LightTouch.indd 13 16/11/22 17:00
Light Touch Switches/EVPAW
2
(
0.385
)
3.8
2.7
(1.9)
A'A
Circuit diagram
The thickness of the solder stencil shall be 0.1 mm,
and the opening ratio of the solder stencil to a land
pattern shall be 60 to 100 % (recommend 80 %.)
without the film
and remainder
of the gate
0.6±0.1
A’A
Land pattern plan
(
2
)
2-1.5
3.3
(
2-0.8
)
2-1.3
(
φ0.85
)
There should be cutout
on the terminal
3
3.5
Without film
0.04±0.03
0.1max.
0.1max.
General dimension tolerance : ± 0.05
( )dimensions are reference dimensions.
This reference specifications are subject to change.
: No soldering area
: Recommended land pattern area
Soldering failure may occur depending on applied
solder amount, so, please consider to use our
recommended stencil and land pattern desing.
t Any land pattern or via holes shall not be provided
at area.
t If it's necessary to design land pattern or via holes
at area, please apply resist to them to protect
their metal part completely.
t If their metal parts are not protected completely,
short circuit failure may occur,
t Besides, there should be convexoconcave by
designing additional pattern,
it may cause swith tilt,
influence on solder-ability or flux intrusion after
reflow soldering.
t Therefore, please study any influence of additioan
land pattern or via holes at area in advance.
No Soldering area
■ Dimensions in mm (not to scale)
Part Numbers Operating Force Height Operating Life
EVPAWBD4A 1.6 N
0.6
mm
EVPAWCD4A
2.4 N
0.6
mm
EVPAWED4A 3.3 N
0.6
mm
EVPAW
(
Embossed Taping)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB14E 201611-Fd
 
Panasonic Corporation 2016
Panasonic Corporation
Electromechanical Control Business Division
–2–
industrial.panasonic.com/ac/e/
500,000 cycles
500,000 cycles
300,000 cycles
LightTouch.indd 14 16/11/22 17:00
Light Touch Switches/EVPAW
180
260
MAX.
150
230
90±30 40±10
(Normal Temp.)
Operation Top (°C)
Soldering Time (s)
Fan or Normal Temp.
Tape width=12.0 mm
Taping condition : Lack of products in the middle of taping should be
one MAX, but total quantity specified in the
specifications should be secured.
Peeling off strength of top tape : It should be within 0.2N to 1. ON at
165 degree in peeling off angle.
Joint of carrier tape : One joint per one reel may exist.
φ
G
D
Feeding hole
K
C
F
A
HE
I
B
J
t
Chip pocket
Tape running direction
● Embossed Carrier Taping
■ Recommended Reflow Soldering Conditions
Unit: mm
Part No.HeightABCDEFGH I JK t
EVPAW 0.6 12.0±0.3 1.75±0.10 5.5±0.1 8.0±0.1 4.0±0.1 2.0±0.1 1.5±0.3 3.8±0.2 2.3±0.2 0.75±0.20 (10.25) 0.3
+0.15
–0.10
＊
Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are withiin the specification.
If even one of them is out of the specifications, please adjust.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB14E 201611-Fd
 
Panasonic Corporation 2016
Panasonic Corporation
Electromechanical Control Business Division
–3–
industrial.panasonic.com/ac/e/
LightTouch.indd 15 16/11/22 17:00
P1-P3

EVP-AWED4A

Mfr. #:
Buy EVP-AWED4A
Manufacturer:
Panasonic
Description:
3.0MM X 2.0MM / 3.3N / 0.15MM ST
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet