Engineering Bulletin
Tentative
No.840A/Mar.2014
Vertical Surface Mount Type
Aluminum Electrolytic Capacitors
Please contact us for mass production schedule.
Specications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1669
1
Alchip
TM
-
MZR
Series
●
Downsizing and Lower ESR, 2,000 hours at 105
℃
●
Rated voltage range : 6.3 to 50V, Nominal capacitance range : 150 to 2,200μF
●
Solvent resistant type
●
Vibration resistant structure
●
RoHS Compliant
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
6.3 to 50V
dc
Capacitance Tolerance
±20%
（
M
）
(at 20
℃
, 120Hz)
Leakage Current
I=0.01CV or 3μA, which is greater.
Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V) (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
Rated voltage (V
dc
) 6.3V 10V 16V 25V 35V 50V
tan
δ
(Max.) 0.26 0.19 0.16 0.14 0.12 0.10
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (V
dc
) 6.3V 10V 16V 25V 35V 50V
Z(-25
℃
)/Z(+20
℃
) 2 2 2 2 2 2
Z(-40
℃
)/Z(+20
℃
) 3 3 3 3 3 3
Z(-55
℃
)/Z(+20
℃
) 4 4 4 3 3 3 (at 120Hz)
Endurance
The following specications shall be satised when the capacitors are restored to 20
℃
after the rated voltage is applied for 2,000 hours
at 105
℃
.
Capacitance change
≦
±30
％
of the initial value
D.F. (tan
δ
)
≦
200
％
of the initial specied value
Leakage current
≦
The initial specied value
Shelf Life
The following specications shall be satised when the capacitors are restored to 20
℃
after exposing them for 1,000 hours at 105
℃
without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦
±30
％
of the initial value
D.F. (tan
δ
)
≦
200
％
of the initial specied value
Leakage current
≦
The initial specied value
Surge Voltage Test
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specied surge voltage for 30±5 seconds
through a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35
℃
.
Rated voltage (V
dc
) 6.3V 10V 16V 25V 35V 50V
Surge voltage (V
dc
) 7.2V 12V 18V 29V 40V 57V
Appearance No signicant damage
Capacitance change
≦
±20
％
of the initial value
D.F. (tan
δ
)
≦
200
％
of the initial specied value
Leakage current
≦
The initial specied value
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specic conditions.It does not
imply long-term use at all.
Size
Code
D L A B C W P
F80 6.3 7.7 6.6 6.6 7.2 0.5
to
0.8 1.9
HA0 8 10.0 8.3 8.3 9.0 0.7
to
1.1 3.1
JA0 10 10.0 10.3 10.3 11.0 0.7
to
1.1 4.5
330
V
ZR
⊕
⊖
3Q
◆
MARKING
EX) 35V330μF
●Rated voltage symbol
Rated voltage(V
dc
) 6.3 10 16 25 35 50
Symbol j A C E V H
◆
DIMENSIONS
［
mm
］
●Terminal Code : A
●Size code : F80 to JA0
●Terminal Code : G
(
Vibration resistant structure
)
●Size code : HA0 to JA0
φ
D±0.5
0.3max.
L±0.5
B±0.2
⊖
A±0.2
⊕
W
C±0.2
P
: Dummy terminals
Vent for JA0
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specied surge voltages may cause to have short circuit failure.
A protection circuit should be used if applied voltage will exceed the rated voltages.
Note
: L±0.3 for F80
φ
D±0.5
0.3max.
L±0.5(Note)
B±0.2
C±0.2
P
⊖
⊕
A±0.2
W
Vent for JA0
