SPECIFICATION
MODEL
OUTPUT
SET UP TIME
Note.4
VOLTAGE RANGE Note.3
FREQUENCY RANGE
POWER FACTOR
(Typ.)
EFFICIENCY (Typ.)
AC CURRENT(Typ.)
INPUT
INRUSH CURRENT
(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
Note.5
EMC IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
OVER TEMPERATURE
500ms/230VAC
(Please refer to "STATIC CHARACTERISTIC" section)
47 ~ 63Hz
PF 0.95/230VAC@load 50%; PF 0.92/277VAC@load 75%≧≧≧≧
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
0.48A / 230VAC 0.36A/277VAC
<0.75mA / 277VAC
Compliance to
EN55015,EN61000-3-2 Class C (@load 50%) ; EN61000-3-3;GB/T17743,GB17625.1≧ ,EAC TP TC 020
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
360 30**21mm (L*W*H)
ENVIRONMENT
EMC EMISSION
Note.5
SAFETY &
EMC
PROTECTION
SHORT CIRCUIT
90%(230VAC@Full load)
Hiccup mode or constant current limiting ,recovers automatically after fault condition is removed
I/P-O/P:3.75KVAC I/P-FG:2.0KVAC O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
File Name:LDC-80-SPEC 2018-05-10
CURRENT TOLERANCE
±5.0%
THD< 10%(@load 50%/230VAC; @load 75%/277VAC)≧≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
TOTAL HARMONIC DISTORTION
OPEN CIRCUIT VOLTAGE
(max.)
COLD START 55A(twidth= s measured at 50% Ipeak)/230VAC300 Per NEMA 410μ;
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
6 units (circuit breaker of type B) / 11 units (circuit breaker of type C) at 230VAC
Tcase=-25 ~ +85 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
MAX. CASE TEMP.
Tcase=+85℃
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity:Line-Earth:2KV,Line-Line:1KV) criteria A,EAC TP TC 020
UL8750 ENEC EN61347-1, EN61347-2-13, ;, CSA C22.2 No. 250.13-12; AS/NZS 61347.1:2016, AS/NZS IEC 61347.2.13:2013
EN62384; GB19510.14,GB19510.1 approved, EAC TP TC 004
1. All parameters NOT specially mentioned are measured at 230VAC input, rated and 25 of ambient temperature.current ℃
2. Please refer to " ".OUTPUT CURRENT SETTING
3. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
4. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. This series meets the typical life expectancy of >50000 hours of operation when Tcase, particularly point (or TMP, per DLC), is about 75 or less.℃tc
7. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
0.295Kg; 40pcs/12.8Kg/0.81CUFT
3.0% max. @rated current
180 ~ 295VAC
LDC-80 series
LDC-80
60V
80W Constant Power MODE Linear LED Driver
Compliance to IEC62386-101.102.207 for DA-Type only
DALI STANDARDS
DIMMING
FUNCTION
By external NTC, please refer to TEMPERATURE COMPENSATION OPERATION section“”
Please refer to DIMMING OPERATION”section“
CURRENT RIPPLE
Shut down o/p voltage, with auto-recovery
1065K hrs min. Telcordia SR-332 (Bellcore) 259Khrs min. MIL-HDBK-217F (25 )℃
OVER VOLTAGE
Shut down o/p voltage with auto-recovery or re-power on to recovery
61 ~ 80V
TEMP. COMPENSATION
LOW FREQUENCY
OUTPUT CURRENT REGION
RATED POWER Note.2
CONSTANT CURRENT REGION
Note.2
27 ~ 56V
700 ~ 2100mA(700mA default)
80W
FULL POWER CURRENT RANGE
1400 ~ 2100mA
