OMO ElectronicOMO Electronic
Expand menu
0 Cart

SE5007T-R

P1-P3P4-P6P7-P9P10-P11
DATA SHEET
SE5007T: 5 GHz Front End Module with Power Detector
Skyworks Solutions, Inc. ● Phone [781] 376-3000 ● Fax [781] 376-3100 ● sales@skyworksinc.com ● www.skyworksinc.com
DST-00383 Rev 2.0 ● Skyworks Proprietary Information ● Products and Product Information are Subject to Change Without Notice ● April 3, 2012 1 of 11
Applications
5 GHz WLAN (IEEE802.11a/g/n)
Access Points, PCMCIA, PC cards
Features
5GHz Front End Module with PA, LNA and T/R
Switch
Integrated power amplifier enable pin (V
EN)
Buffered, temperature compensated power
detector
High and Low-Linearity mode
3% EVM, @17dBm, 64 QAM, 54 Mbps
30 dB Typical Gain
Lead Free and RoHS compliant, halogen free
package
16 pin 3 mm x 3 mm x 0.6 mm QFN, MSL1
Ordering Information
Part Number Package Remark
SE5007T 16 Pin QFN Samples
SE5007T-R 16 Pin QFN Tape and Reel
SE5007T-EK1 Evaluation Kit Standard
Product Description
The SE5007T is a 5GHz front end module offering
high linear power for wireless LAN applications. It
incorporates a power detector for control of the output
power.
The SE5007T offers a high level of integration for a
simplified design, providing quicker time to market
and higher application board production yield. The
device integrates the input match, inter-stage match,
a temperature compensated, load insensitive power
detector with 20dB of dynamic range, a 3.8GHz notch
filter, a T/R switch and LNA.
For wireless LAN applications, the device meets the
requirements of IEEE802.11a and delivers
approximately 17dBm of linear output power. It also
features a low linearity mode control to reduce current
consumption at low power modes.
The SE5007T integrates the reference voltage
generator, allowing for a true 1.8V CMOS compatible
digital EN (enable) function to turn the power amplifier
on and off.
Functional Block Diagram
Figure 1: Functional Block Diagram
Match &
Filter
Match
Bias, Enable, Detector Circuits
VCC1,2
EN
TXIN
C0 C1
ANT
RX
H/L Lin DET
DATA SHEET
SE5007T: 5 GHz Front End Module with Power Detector
Skyworks Solutions, Inc. ● Phone [781] 376-3000 ● Fax [781] 376-3100 ● sales@skyworksinc.com ● www.skyworksinc.com
DST-00383 Rev 2.0 ● Skyworks Proprietary Information ● Products and Product Information are Subject to Change Without Notice ● April 3, 2012 2 of 11
Pin Out Diagram
Figure 2: SE5007T Pin-Out Diagram
Pin Out Description
Pin
No.
Name Description
Pin
No.
Name Description
1 EN PA Enable 9 VDD LNA Supply Voltage
2 GND Ground 10 GND Ground
3 TXIN 5GHz TX RF Input Signal 11 ANT 5GHz Antenna output
4 GND Ground 12 GND Ground
5 RX 5GHz LNA Output Signal 13 DET Power Detector Output
6 GND Ground 14 H/L Lin High-Low linearity Control
7 C0 Switch Control Logic 1 15 VCC1 Power Stage Supply Voltage
8 C1 Switch Control Logic 2 16 VCC2 Bias, Driver Stage Supply Voltage
DATA SHEET
SE5007T: 5 GHz Front End Module with Power Detector
Skyworks Solutions, Inc. ● Phone [781] 376-3000 ● Fax [781] 376-3100 ● sales@skyworksinc.com ● www.skyworksinc.com
DST-00383 Rev 2.0 ● Skyworks Proprietary Information ● Products and Product Information are Subject to Change Without Notice ● April 3, 2012 3 of 11
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may
cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the
recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this
device should be at ESD protected workstations.
Symbol Definition Min. Max. Unit
VCC1 Supply Voltage on pin 15 (VCC1) 3.0 4.8 V
VDD, VCC2 Supply Voltage on pins 9, 16 (VDD, VCC2) 3.0 3.6 V
EN DC input on Enable -0.3 3.6 V
TXIN RF Input Power, RFout into 50 match - 12 dBm
TSTG Storage Temperature Range -40 150 °C
ESD
HBM
JEDEC JESD22-A114
all pins
Antenna Pin - 1000
V
All Other Pins - 300
Recommended Operating Conditions
Symbol Parameter Min. Max. Unit
VCC1 Supply Voltage on pin 15 (VCC1) 3.0 4.5 V
VDD, VCC2 Supply Voltage on pins 9, 16 (VDD, VCC2) 3.0 3.6 V
TA Ambient Temperature -40 85 °C
Control Logic Characteristics
Conditions: VCC1
= VCC2
= VDD
= VPAON = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5007T-
EV1 evaluation board, unless otherwise noted.
Symbol Parameter Conditions Min. Typ. Max. Unit
ICC-802.11a
Supply Current,
Transmit Mode
P
OUT
= 17 dBm, 54 Mbps, 64 QAM,
H/L Lin = 3.3V (High Linearity Mode)
- 195 -
mA
P
OUT
= 13 dBm, 54 Mbps, 64 QAM,
H/L Lin = 0V (Low Linearity Mode)
- 140 -
P
OUT
= 5 dBm, 54 Mbps, 64 QAM,
H/L Lin = 0V (Low Linearity Mode)
- 105 -
P
OUT
= 19 dBm, 54 Mbps, 64 QAM,
H/L Lin = 3.3V, VCC1 = 4.0V
220
Supply Current,
Receive Mode
VEN = C0 = 0V; C1 = 3.3V 15
VEN = C0 = C1 = 0V 0.02
IOFF Supply Current
VEN = 0 V, No RF, C0=C1=0 V
Measured on VCC, VDD pins
- 20 50 A
VENH Logic High Voltage - 1.6 - 3.6 V
VENL Logic Low Voltage - -0.3 - 0.3 V
IENH
Input Current Logic
- - 330 400 A
P1-P3P4-P6P7-P9P10-P11

SE5007T-R

Mfr. #:
Buy SE5007T-R
Manufacturer:
Skyworks Solutions, Inc.
Description:
RF Front End 5GHz 24dBm Gain 30 dB typ.
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet