OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AAA3528LSEEZGKQBKS

P1-P3P4-P6P7-P8
SPEC NO: DSAO4456 REV NO: V.2B DATE: SEP/18/2015 PAGE: 1 OF 8
APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1201008965
3.5x2.8mm SURFACE MOUNT LED LAMP
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: AAA3528LSEEZGKQBKS
Hyper Red
Green
Blue
Features
z Suitable for all SMD assembly and solder process.
z Available on tape and reel.
z Package: 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Low current IF=2mA operating.
z RoHS compliant.
Descriptions
z The Hyper Red source color devices are made with
AlGaInP on GaAs substrate Light Emitting Diode.
z The Green source color devices are made with InGaN
on Sapphire Light Emitting Diode.
z The Blue source color devices are made with InGaN on
Sapphire Light Emitting Diode.
z Electrostatic discharge and power surge could damage
the LEDs.
z It is recommended to use a wrist band or anti-
electrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAO4456 REV NO: V.2B DATE: SEP/18/2015 PAGE: 2 OF 8
APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1201008965
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly Orangeuces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H
2
S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAO4456 REV NO: V.2B DATE: SEP/18/2015 PAGE: 3 OF 8
APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1201008965
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2.Forward Voltage: +/-0.1V.
3.Wavelength value is traceable to the CIE127-2007 compliant national standards.
4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Emitting Color (Material) Lens Type
Iv (mcd) [2]
@ 2mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AAA3528LSEEZGKQBKS
Hyper Red (AlGaInP)
Water Clear
10 20
Green (InGaN) 80 180
Blue (InGaN) 12 30
120
°
Symbol Parameter Emitting Color Typ. Max. Units Test Conditions
λpeak Peak Wavelength
Hyper Red
Green
Blue
630
515
460
nm I
F=2mA
λD [1] Dominant Wavelength
Hyper Red
Green
Blue
621
525
465
nm I
F=2mA
Δλ1/2 Spectral Line Half-width
Hyper Red
Green
Blue
20
35
25
nm I
F=2mA
C Capacitance
Hyper Red
Green
Blue
25
45
100
pF V
F=0V;f=1MHz
V
F [2] Forward Voltage
Hyper Red
Green
Blue
1.8
2.65
2.65
2.1
3.1
3.1
V IF=2mA
I
R Reverse Current
Hyper Red
Green
Blue
10
50
50
uA VR=5V
Parameter Hyper Red Green Blue Units
Power dissipation 105 93 93 mW
DC Forward Current 50 30 30 mA
Peak Forward Current [1] 195 150 150 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
Electrostatic Discharge Threshold (HBM) - V 450 250
P1-P3P4-P6P7-P8

AAA3528LSEEZGKQBKS

Mfr. #:
Buy AAA3528LSEEZGKQBKS
Manufacturer:
Kingbright
Description:
Standard LEDs - SMD 3.5x2.8MM LOW CU RGB SMD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet