NCP1086
http://onsemi.com
2
MAXIMUM RATINGS*
Parameter Value Unit
Supply Voltage, V
CC
7.0 V
Operating Temperature Range −40 to +70 °C
Junction Temperature 150 °C
Storage Temperature Range −60 to +150 °C
Lead Temperature Soldering: Wave Solder (through hole styles only) Note 1
Reflow (SMD styles only) Note 2
260 Peak
230 Peak
°C
ESD Damage Threshold 2.0 kV
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 10 second maximum.
2. 60 second maximum above 183°C.
ELECTRICAL CHARACTERISTICS (C
IN
= 10 mF, C
OUT
= 22 mF Tantalum, V
OUT
+ V
DROPOUT
< V
IN
< 7.0 V, 0°C ≤ T
A
≤ 70°C,
T
J
≤ +150°C, unless otherwise specified, I
full
load
= 1.5 A.)
Characteristic
Test Conditions Min Typ Max Unit
ADJUSTABLE OUTPUT VOLTAGE
Reference Voltage (Notes 3 and 4)
V
IN
− V
OUT
= 1.5 V; V
Adj
= 0 V,
10 mA ≤ I
OUT
≤ 1.5 A
1.241
(−1%)
1.254 1.266
(+1%)
V
Line Regulation 1.5 V ≤ V
IN
− V
OUT
≤ 5.75 V; I
OUT
= 10 mA − 0.02 0.2 %
Load Regulation (Notes 3 and 4) V
IN
− V
OUT
= 1.5 V; 10 mA ≤ I
OUT
≤ 1.5 A − 0.04 0.4 %
Dropout Voltage (Note 5) I
OUT
= 1.5 A − 1.05 1.4 V
Current Limit V
IN
− V
OUT
= 3.0 V; T
J
≥ 25°C 1.6 3.1 − A
Minimum Load Current (Note 6) V
IN
= 7.0 V; V
Adj
= 0 − 0.6 2.0 mA
Adjust Pin Current V
IN
− V
OUT
= 3.0 V; I
OUT
= 10 mA − 50 100
mA
Thermal Regulation (Note 7) 30 ms pulse; T
A
= 25°C − 0.002 0.02 %/W
Ripple Rejection (Note 7) f = 120 Hz; I
OUT
= 1.5 A; V
IN
− V
OUT
= 3.0 V;
V
RIPPLE
= 1.0 V
P−P
− 80 − dB
Thermal Shutdown (Note 8) − 150 180 210 °C
Thermal Shutdown Hysteresis (Note 8) − − 25 − °C
FIXED OUTPUT VOLTAGE
Output Voltage (Notes 3 and 4)
V
IN
− V
OUT
= 1.5 V, 0 ≤ I
OUT
≤ 1.5 A 3.25
(−1.5%)
3.3 3.35
(+1.5%)
V
Line Regulation 2.0 V ≤ V
IN
− V
OUT
≤ 3.7 V; I
OUT
= 10 mA − 0.02 0.2 %
Load Regulation (Notes 3 and 4) V
IN
− V
OUT
= 2.0 V; 10 mA ≤ I
OUT
≤ 1.5 A − 0.04 0.4 %
Dropout Voltage (Note 5) I
OUT
= 1.5 A − 1.05 1.4 V
Current Limit V
IN
− V
OUT
= 3.0 V 1.6 3.1 − A
Quiescent Current I
OUT
= 10 mA − 5.0 10 mA
Thermal Regulation (Note 7) 30 ms pulse; T
A
= 25°C − 0.002 0.02 %/W
3. Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output
voltage due to thermal gradients or temperature changes must be taken into account separately.
4. Specifications apply for an external Kelvin sense connection at a point on the output pin 1/4” from the bottom of the package.
5. Dropout voltage is a measurement of the minimum input/output differential at full load.
6. The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider used to set the
output voltage is selected to meet the minimum requirement.
7. Guaranteed by design, not 100% tested in production.
8. Thermal shutdown is 100% functionally tested in production.