5
FN8085.8
September 12, 2008
V
IH
SDA and SCL Input Buffer HIGH
Voltage
0.7 x
V
DD
V
DD
+
0.3
V
Hysteresis SDA and SCL Input Buffer
Hysteresis
0.05 x
V
DD
V
V
OL
SDA Output Buffer LOW Voltage,
Sinking 3mA
00.4V
C
PIN
SDA and SCL Pin Capacitance T
A
= +25°C, f = 1MHz, V
DD
= 5V, V
IN
=0V,
V
OUT
= 0V
10, 11 10 pF
f
SCL
SCL Frequency 400 kHz
t
IN
Pulse width Suppression Time at
SDA and SCL Inputs
Any pulse narrower than the max spec is
suppressed.
50 ns
t
AA
SCL Falling Edge to SDA Output
Data Valid
SCL falling edge crossing 30% of V
DD
, until
SDA exits the 30% to 70% of V
DD
window.
900 ns
t
BUF
Time the Bus Must Be Free Before
the Start of a New Transmission
SDA crossing 70% of V
DD
during a STOP
condition, to SDA crossing 70% of V
DD
during the following START condition.
1300 ns
t
LOW
Clock LOW Time Measured at the 30% of V
DD
crossing. 1300 ns
t
HIGH
Clock HIGH Time Measured at the 70% of V
DD
crossing. 600 ns
t
SU:STA
START Condition Setup Time SCL rising edge to SDA falling edge. Both
crossing 70% of V
DD
.
600 ns
t
HD:STA
START Condition Hold Time From SDA falling edge crossing 30% of V
DD
to SCL falling edge crossing 70% of V
DD
.
600 ns
t
SU:DAT
Input Data Setup Time From SDA exiting the 30% to 70% of V
DD
window, to SCL rising edge crossing 30% of
V
DD
100 ns
t
HD:DAT
Input Data Hold Time From SCL falling edge crossing 30% of V
DD
to SDA entering the 30% to 70% of V
DD
window.
20 900 ns
t
SU:STO
STOP Condition Setup Time From SCL rising edge crossing 70% of V
DD
,
to SDA rising edge crossing 30% of V
DD
.
600 ns
t
HD:STO
STOP Condition Hold Time From SDA rising edge to SCL falling edge.
Both crossing 70% of V
DD
.
600 ns
t
DH
Output Data Hold Time From SCL falling edge crossing 30% of V
DD
,
until SDA enters the 30% to 70% of V
DD
window.
0ns
t
R
SDA and SCL Rise Time From 30% to 70% of V
DD
10, 11 20 +
0.1 x Cb
300 ns
t
F
SDA and SCL Fall Time From 70% to 30% of V
DD
10, 11 20 +
0.1 x Cb
300 ns
Cb Capacitive Loading of SDA or SCL Total on-chip and off-chip 10, 11 10 400 pF
Rpu SDA and SCL Bus Pull-Up
Resistor Off-Chip
Maximum is determined by t
R
and t
F
.
For Cb = 400pF, max is about 2kΩ to~2.5kΩ.
For Cb = 40pF, max is about 15kΩ to ~20kΩ
10, 11 1 kΩ
NOTES:
5. IRQ
and F
OUT
Inactive.
6. LPMODE = 0 (default).
7. In order to ensure proper timekeeping, the V
DD SR-
specification must be followed.
8. Typical values are for T = +25°C and 3.3V supply voltage.
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
10. Parameter is not 100% tested.
11. These are I
2
C specific parameters and are not tested, however, they are used to set conditions for testing devices to validate specification.
Serial Interface Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL PARAMETER TEST CONDITIONS NOTES
MIN
(Note 9)
TYP
(Note 8)
MAX
(Note 9) UNITS
ISL1208