File Name:ISI-501-SPEC 2018-01-15
500W True Sine Wave DC-AC Inverter with MPPT Solar Charger
ISI-501 series
ISI-501-112□ ISI-501-124□ ISI-501-148□ ISI-501-212□ ISI-501-224□ ISI-501-248□
200 / 220 / 230 / 240VAC selectable by setting button S.W
50 0.1Hz 50/60Hz selectable by setting button S.W±
15A30A 30A50A 50A 15A
48V24V 24V12V 12V 48V
42 ~ 60VDC21 ~ 30VDC 21 ~ 30VDC10.5 ~ 15VDC 10.5 ~ 15VDC 42 ~ 60VDC
87%87%85% 88%88%86%
MODEL
MAXIMUM OUTPUT POWER (Typ.)
WAVEFORM Note.1
OUTPUT
INVERTER
SECTION
FREQUENCY
AC REGULATION (Typ.)
FRONT PANEL INDICATOR
NO LOAD CURRENT DRAW (Typ.)
BAT. VOLTAGE
EFFICIENCY (Typ.)
Note.2
OFF MODE CURRENT DRAW (Typ.)
DC CURRENT (Typ.) Note.7
VOLTAGE RANGE Note.3,5
INPUT
OUTPUT
OVER TEMPERATURE
OUTPUT SHORT
100 / 110 / 115 / 120VAC selectable by setting button S.W
550W for 60 sec. / surge power 1000W for 30 cycles (112, 212 models : 495W for 60 sec. / surge power 900W for 30 cycles)
True sine wave (THD<3%)
60 0.1Hz 50/60Hz selectable by setting button S.W±
±
3%
Fault and operation status, Charger status, Battery capacity
1.25A 0.63A 0.32A 1.25A 0.63A 0.32A
≦1mA
Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
RATED POWER 450W 450W500W 500W
OVER LOAD (Typ.)
110% load for 60 sec.
Protection type : Shut down o/p voltage, re-power on to recover
OTHERS
PACKING
2.35Kg; 6pcs/15.1Kg/1.55CUFT
DIMENSION
205*158*67mm (L*W*H)
NOTE
1.THD is tested by rated power, linear load at 13V,26V,52V input voltage.
2.Efficiency is tested by 350W, linear load at 13V,26V,52V input voltage.
3.The tolerance of each voltage value by models
is : 112/212 0.5V ; 124/224 1V ; 148/248 2V.→± →± →±
4.Output derating capacity referenced by curve 1.
5.Input derating capacity referenced by curve 2.
6.All parameters not specified above are measured at rated load, 25 of ambient temperature and set to factory setting.
℃
7.DC current is tested by 500W, linear load at 12V,24V,48V input voltage.
8.The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than ℃℃
2000m(6500ft).
AC VOLTAGE
Factory setting set at 110VAC
Factory setting set at 110VAC
Factory setting set at 230VAC
Factory setting set at 230VAC
PROTECTION
FUSE
CHARGER CURRENT (Typ.)
BATTERY TYPE
BAT. LOW ALARM Note.3
BAT. LOW SHUTDOWN Note.3
REVERSE POLARITY
MPPT CHARGER EFFICIENCY ( )
Typ.
40A*2 40A*1 20A*1 40A*2 40A*1 20A*2
30A 17A 8.5A 30A 17A 8.5A
Open & sealed Lead Acid
11.3V 22.5V 45V 11.3V 22.5V 45V
10.5V 21V 42V 10.5V 21V 42V
By internal fuse open
WORKING TEMP. Note.4
MPPT RANGE
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
-20 ~ +40 @ 100% load ; 60 @ 50% load℃℃
98%
20% ~ 90% RH non-condensing
-30 ~ +70 / -22 ~ +158 F, 10 ~ 95% RH non-condensing℃
o
VIBRATION
10 ~ 500Hz, 3G 10min./1cycle, 60min. each along X, Y, Z axes
ENVIRONMENT
Compliance to FCC part 15 class B, EAC TP TC 020
Compliance to EAC TP TC 020
LVD
SAFETY STANDARDS
None
EAC TP TC 004 approved
Compliance to EN61000-4-2,3,8, EAC TP TC 020
Compliance to EN55032 class B, EAC TP TC 020
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
Bat I/P - AC O/P:3.0KVAC AC O/P - FG:1.5KVAC
Bat I/P - AC O/P, Bat I/P - FG, AC O/P - FG: 100M ohms / 500VDC / 25 / 70% RH℃
EN60950-1 (LVD)
EMC IMMUNITY
EMC EMISSION
GENERAL
MPPT / SOLAR
BATTERY SECTION
SECTION
SECTION
35 ~ 50V
25 ~ 50V
45 ~ 90V
35 ~ 90V
90 ~ 160V
70 ~ 160V
35 ~ 50V
25 ~ 50V
45 ~ 90V
35 ~ 90V
90 ~ 160V
70 ~ 160V
11A
500W
7A 4.5A 11A 7A 4.5A
OPEN CIRCUIT VOLTAGE RANGE
SOLAR INPUT CURRENT (Typ.)
SOLAR INPUT POWER (Typ.)
SAFETY
&
EMC
MTBF
57.8K hrs min. MIL-HDBK-217F (25 )℃
TYPE-A
Standard
Receptacle type
Country
Certificate
TYPE-B
Standard
TYPE-C
Optional
TYPE-D
Optional
TYPE-E
Optional
TYPE-F
Optional
USA
EUROPE
AUSTRALIA
U.K
JAPAN GFCI
AC Output Receptacles(Optional)
Optional
TYPE-U
UNIVERSAL
Non
SPECIFICATION
