4
LT1464/LT1465
ELECTRICAL CHARACTERISTICS
V
S
= ±15V, V
CM
= 0V, 0°C ≤ T
A
≤ 70°C, unless otherwise noted.
LT1464AC LT1464C/LT1465C
SYMBOL PARAMETER CONDITIONS (Note 1) MIN TYP MAX MIN TYP MAX UNITS
∆CMRR Common Mode Rejection Match (Notes 5, 7) ● 73 84 70 84 dB
∆PSRR Power Supply Rejection Match (Notes 5, 7) ● 77 85 73 85 dB
V
S
= ±15V, V
CM
= 0V, –40°C ≤ T
A
≤ 85°C (Note 2), unless otherwise noted.
LT1464AC LT1464C/LT1465C
SYMBOL PARAMETER CONDITIONS (Note 1) MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage V
S
= ±5V ● 0.6 1.5 0.6 1.5 mV
V
S
= ±15V ● 1.0 3.0 1.0 3.0 mV
∆V
OS
Average Input Offset Voltage Drift (Note 6) ● 720 720µV/°C
∆Temp
I
OS
Input Offset Current ● 40 150 60 700 pA
I
B
Input Bias Current ● 200 500 300 2500 pA
CMRR Common Mode Rejection Ratio V
CM
= –12V to 15V ● 74 84 72 84 dB
PSRR Power Supply Rejection Ratio V
S
= ±3V to ±20V ● 79 88 76 88 dB
A
VOL
Large-Signal Voltage Gain V
O
= ±10V, R
L
= 10k ● 175 400 175 400 V/mV
V
O
= ±10V, R
L
= 2k ● 80 250 80 250 V/mV
V
S
= ±5V, V
O
= ±2V, R
L
= 10k ● 70 180 70 180 V/mV
V
S
= ±5V, V
O
= ±1V, R
L
= 2k ● 45 140 45 140 V/mV
V
OUT
Output Voltage Swing R
L
= 10k ● ±13.2 ±13.4 ±13.2 ±13.4 V
R
L
= 2k ● ±13.0 ±13.2 ±13.0 ±13.2 V
V
S
= ±5V, R
L
= 2k ● ±3.2 ±3.4 ±3.2 ±3.4 V
SR Slew Rate R
L
= 10k (Note 4) ● 0.35 0.7 0.35 0.7 V/µs
GBW Gain Bandwidth Product f = 10kHz ● 510 850 510 850 kHz
I
S
Supply Current per Amplifier ● 165 230 165 230 µA
V
S
= ±5V ● 160 230 160 230 µA
V
OS
Offset Voltage Match (Note 7) V
S
= ±5V ● 0.8 2.5 0.8 2.5 mV
V
S
= ±15V ● 1.0 4.0 1.0 4.0 mV
∆I
B
+
Noninverting Bias Current Match ● 20 100 70 800 pA
(Note 7)
∆CMRR Common Mode Rejection Match (Notes 5, 7) ● 72 83 69 83 dB
∆PSRR Power Supply Rejection Match (Notes 5, 7) ● 76 81 73 81 dB
The ● denotes specifications which apply over the full operating
temperature range.
Note 1: Typical parameters are defined as 60% yield of parameter
distributions of individual amplifiers, i.e., out of 100 LT1465s (or 100
LT1464s) typically 240 op amps (or 120) will be better than the indicated
specification.
Note 2: The LT1464 and LT1465 are designed, characterized and expected
to meet these extended temperature limits, but are not tested at –40°C
and 85°C. Guaranteed I grade parts are available, consult factory.
Note 3: Current noise is calculated from the formula: i
n
= (2qi
b
)
1/2
where
q = (1.6)(10)
–19
coulomb. The noise of source resistors up to 1GΩ
swamps the contribution of current noise.
Note 4: Slew rate is measured in A
V
= –1; input signal is ±7.5V, output is
measured at ±2.5V.
Note 5: ∆CMRR and ∆PSRR are defined as follows:
1. CMRR and PSRR are measured in µV/V on the individual amplifiers.
2. The difference is calculated between the matching sides in µV/V.
3. The result is converted to dB.
Note 6: This parameter is not 100% tested.
Note 7: Matching parameters are the difference between amplifiers A and
D and between B and C on the LT1465; between the two amplifiers on the
LT1464.