Sensors
Freescale Semiconductor 3
MMA7260QT
Table 2. Operating Characteristics
Unless otherwise noted: –40°C < T
A
< 105°C, 2.2 V < V
DD
< 3.6 V, Acceleration = 0g, Loaded output
(1)
Characteristic Symbol Min Typ Max Unit
Operating Range
(2)
Supply Voltage
(3)
Supply Current
Supply Current at Sleep Mode
(4)
Operating Temperature Range
Acceleration Range, X-Axis, Y-Axis, Z-Axis
g-Select1 & 2: 00
g-Select1 & 2: 10
g-Select1 & 2: 01
g-Select1 & 2: 11
V
DD
I
DD
I
DD
T
A
g
FS
g
FS
g
FS
g
FS
2.2
—
—
–40
—
—
—
—
3.3
500
3.0
—
±1.5
±2.0
±4.0
±6.0
3.6
800
10
+105
—
—
—
—
V
μA
μA
°C
g
g
g
g
Output Signal
Zero-g (T
A
= 25°C, V
DD
= 3.3 V)
(5)
Zero-g
(4)
X-axis
Y-axis
Z-axis
Sensitivity (T
A
= 25°C, V
DD
= 3.3 V)
1.5g
2g
4g
6g
Sensitivity
(4)
X-axis
Y-axis
Z-axis
Bandwidth Response
XY
Z
V
OFF
V
OFF
, T
A
S
1.5g
S
2g
S
4g
S
6g
S,T
A
f
-3dB
f
-3dB
1.485
±2.6
(6)
±5.8
(6)
±1.0
(6)
740
555
277.5
185
±0.02
(6)
±0.01
(6)
±0.01
(6)
—
—
1.65
±0.6
±5.8
±0.8
800
600
300
200
±0.02
±0.01
±0.00
350
150
1.815
±3.8
(7)
±5.9
(7)
±0.8
(7)
860
645
322.5
215
±0.02
(7)
±0.01
(7)
±0.01
(7)
—
—
V
mg/°C
mV/g
mV/g
mV/g
mV/g
%/°C
Hz
Hz
Noise
RMS (0.1 Hz – 1 kHz)
(4)
Power Spectral Density RMS (0.1 Hz – 1 kHz)
(4)
n
RMS
n
PSD
—
—
4.7
350
—
—
mVrms
μg/
Control Timing
Power-Up Response Time
(8)
Enable Response Time
(9)
Sensing Element Resonant Frequency
XY
Z
Internal Sampling Frequency
t
RESPONSE
t
ENABLE
f
GCELL
f
GCELL
f
CLK
—
—
—
—
—
1.0
0.5
6.0
3.4
11
2.0
2.0
—
—
—
ms
ms
kHz
kHz
kHz
Output Stage Performance
Full-Scale Output Range (I
OUT
= 30 µA) V
FSO
V
SS
+0.25
—
V
DD
–0.25 V
Nonlinearity, X
OUT
, Y
OUT
, Z
OUT
NL
OUT
–1.0 — +1.0 %FSO
Cross-Axis Sensitivity
(10)
V
XY, XZ, YZ
——5.0 %
Ratiometric Error
(11)
error — — — %
1. For a loaded output, the measurements are observed after an RC filter consisting of a 1.0 kΩ resistor and a 0.1 µF capacitor on V
DD
-GND.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
may operate as a linear device but is not guaranteed to be in calibration.
4. This value is measured with g-Select in 1.5g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above V
DD
/2. For negative acceleration, the output will decrease below V
DD
/2.
6. These values represent the 10th percentile, not the minimum.
7. These values represent the 90th percentile, not the maximum.
8. The response time between 10% of full scale V
DD
input voltage and 90% of the final operating output voltage.
9. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
10. A measure of the device’s ability to reject an acceleration applied 90 from the true axis of sensitivity.
11. Zero-g offset ratiometric error can be typically >20% at V
DD
= 2.2 V. Sensitivity ratiometric error can be typically >3% at V
DD
= 2.2. Consult
factory for additional information
Hz
