ICS87001BG-01 REVISION A JULY 2, 2013 10 ©2013 Integrated Device Technology, Inc.
ICS87001-01 Data Sheet LVCMOS/LVTTL CLOCK DIVIDER
Power Considerations
This section provides information on power dissipation and junction temperature for the ICS87001-01.
Equations and example calculations are also provided.
1. Power Dissipation.
The total power dissipation for the ICS87001-01 is the sum of the core power plus the analog power plus the power dissipated in the load(s).
The following is the power dissipation for V
DD
= 3.3V + 5% = 3.465V, which gives worst case results.
• Power (core)
MAX
= V
DD_MAX
* I
DD
= 3.465V * 55mA = 190.6mW
• Power (output)
MAX
= V
DDO_MAX
* I
DDO
= 3.465V * 5mA = 17.3mW
LVCMOS Output Power Dissipation
• Output Impedance R
OUT
Power Dissipation due to Loading 50 to V
DD
/2
Output Current I
OUT
= V
DD_MAX
/ [2 * (50 + R
OUT
)] = 3.465V / [2 * (50 + 17)] = 25.9mA
• Power Dissipation on the R
OUT
per LVCMOS output
Power (R
OUT
) = R
OUT
* (I
OUT
)
2
= 17 * (25.9mA)
2
= 11.4mW
• Total Power (R
OUT
) = 11.4mW * 1 = 11.4mW
Dynamic Power Dissipation at f
OUT_MAX
(250MHz)
Power (250MHz) = C
PD
* Frequency * (V
DDO
)
2
= 6pF * 250MHz * (3.465V)
2
= 18mW per output
Total Power (250MHz) = 18mW * 1 = 18mW
Total Power Dissipation
• Total Power
= Power (core)
MAX
+ Power (output)
MAX
+ Total Power (R
OUT
) + Total Power (250MHz)
= 190.6mW + 17.3mW + 11.4mW + 18mW
= 237.3mW
2. Junction Temperature.
Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad directly affects the reliability of the device. The
maximum recommended junction temperature is 125°C. Limiting the internal transistor junction temperature, Tj, to 125°C ensures that the bond
wire and bond pad temperature remains below 125°C.
The equation for Tj is as follows: Tj =
JA
* Pd_total + T
A
Tj = Junction Temperature
JA
= Junction-to-Ambient Thermal Resistance
Pd_total = Total Device Power Dissipation (example calculation is in section 1 above)
T
A
= Ambient Temperature
In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance
JA
must be used. Assuming no air flow and
a multi-layer board, the appropriate value is 100.3°C/W per Table 6 below.
Therefore, Tj for an ambient temperature of 70°C with all outputs switching is:
70°C + 0.237W * 100.3°C/W = 94°C. This is below the limit of 125°C.
This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow and the type of
board (multi-layer).
Table 6. Thermal Resistance
JA
for 16 Lead TSSOP, Forced Convection
JA
by Velocity
Meters per Second 012.5
Multi-Layer PCB, JEDEC Standard Test Boards 100.3°C/W 96.0°C/W 93.9°C/W
