4
FN3137.6
March 4, 2009
Source OFF Leakage
Current, I
S(OFF)
V
EN
= 0V V
S
= +10V, V
D
= -10V -1 0.002 1 -5 0.002 5 nA
V
S
= -10V, V
D
= +10V -1 -0.005 1 -5 -0.005 5 nA
Drain OFF Leakage
Current, I
D(OFF)
V
EN
= 0V V
S
= -10V, V
D
= +10V - 0.01 10 - 0.01 20 nA
V
S
= +10V, V
D
= -10V -10 -0.015 - -20 -0.015 - nA
Drain ON Leakage Current,
I
D(ON)
(Note 6)
Sequence Each
Switch ON
V
AL
= 0.8V,
V
AH
= 2.4V
V
D
= V
S(ALL)
= +10V - 0.015 10 - 0.015 20 nA
V
D
= V
S(ALL)
= -10V -10 -0.03 - -20 -0.03 - nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V
EN
= 5.0V (Enabled) or
V
EN
= 0V (Standby), V
A
= 0V
- 1.3 2.4 - 1.3 2.4 mA
Negative Supply Current, I- -1.5 -0.7 - -1.5 -0.7 - mA
Electrical Specifications T
A
= 25
o
C, V+ = +15V, V- = -15V, GND = 0V, V
EN
= 2.4V, Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
“A” SUFFIX “B” AND “C” SUFFIX
UNITS
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
Electrical Specifications T
A
= Over Operating Temperature Range, V+ = +15V, V- = -15V, GND = 0V, V
EN
= 2.4V,
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
“A” SUFFIX
UNITSMIN
(NOTE 3)
TYP MAX
DIGITAL INPUT CHARACTERISTICS
Address Input Current, Input Voltage
High, I
AH
V
A
= 2.4V -30 - - μA
V
A
= 15V - - 30 μA
Address Input Current Input Voltage
Low, I
AL
V
EN
= 2.4V V
A
= 0V -30 - - μA
V
EN
= 0V -30 - - μA
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
(Note 7) -15 - +15 V
Drain-Source ON Resistance, r
DS(ON)
Sequence Each Switch ON
V
AL
= 0.8V, V
AH
= 2.4V
I
S
= -200μA, V
D
= +10V - - 500 Ω
I
S
= -200μA, V
D
= -10V - - 500 Ω
Source OFF Leakage Current, I
S(OFF)
V
EN
= 0V V
S
= +10V, V
D
= -10V - - 50 nA
V
S
= -10V, V
D
= +10V -50 - - nA
Drain OFF Leakage Current, I
D(OFF)
V
EN
= 0V V
S
= -10V, V
D
= +10V - - 200 nA
V
S
= +10V, V
D
= -10V -200 - - nA
Drain ON Leakage Current, I
D(ON)
(Note 6) Sequence Each Switch ON
V
AL
= 0.8V, V
AH
= 2.4V
V
D
= V
S(ALL)
= +10V - - 200 nA
V
D
= V
S(ALL)
= -10V -200 - - nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V
EN
= 5.0V, V
A
= 0V -3.2 - 4.5 mA
Negative Supply Current, I- -3.2 - 4.5 mA
Positive Standby Supply Current, I+ V
EN
= 0V, V
A
= 0V -3.2 - 4.5 mA
Negative Standby Supply Current, I- -3.2 - 4.5 mA
NOTES:
3. Typical values are for design aid only, not guaranteed and not subject to production testing.
4. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.
5. Off isolation = 20Log |V
S
|/|V
D
|, where V
S
= input to Off switch, and V
D
= output due to V
S
.
6. I
D(ON)
is leakage from driver into “ON” switch.
7. Parameter not tested. Parameter guaranteed by design or characterization.
DG508A
