RFM products are now
Murata products.
©2010-2015 by Murata Electronics N.A., Inc.
RF1172C (R) 4/6/15 Page 1 of 2
www.murata.com
Characteristic Sym Notes Minimum Typical Maximum Units
Center Frequency at 25°C Absolute Frequency
f
c
1, 2
433.92 MHz
Tolerance from 433.92 MHz
Δf
C
±160 kHz
Insertion Loss IL 1 3.0 5.0 dB
3 dB Bandwidth
BW
3
1, 2
500 600 800
kHz
Rejection
at f
c
- 21.4 MHz (Image)
1
40 50
dBat f
c
- 10.7 MHz (LO)
30 40
Ultimate 80
Temperature Operating Case Temp.
T
C
3, 4
-40 +85 °C
Turnover Temperature
T
O
15 25 35 °C
Turnover Frequency
f
O
f
c
MHz
Freq. Temp. Coefficient
FTC
0.032 ppm/°C
2
Frequency Aging Absolute Value during the First Year |fA| 5 ≤10 ppm/yr
Impedance @ fc
Input Z
IN
= R
IN
llC
IN
Z
IN
1
212 Ω ll 3.1 pF
Output Z
OUT
= R
OUT
llC
OUT
Z
OUT
212 Ω ll 3.1 pF
Lid Symbolization (Y=year WW=week S=shift) 409 // YWWS
Standard Reel Quantity Reel Size 7 Inch
9
500 Pieces/Reel
Reel Size 13 Inch 3000 Pieces/Reel
• Ideal Front-End Filter for European Wireless Receivers
• Low-Loss, Coupled-Resonator Quartz Design
• Simple External Impedance Matching
• Complies with Directive 2002/95/EC (RoHS)
The RF1172C is a low-loss, compact, and economical surface-acoustic-wave (SAW) filter
designed to provide front-end selectivity in 433.92 MHz receivers. Receiver designs using this
filter include superhet with 10.7 MHz or 500 kHz IF, direct conversion and superregen. Typical
applications of these receivers are wireless remote-control and security devices operating in
Europe under ETSI I-ETS 300 220.
This coupled-resonator filter (CRF) uses selective null placement to provide suppression, typically
greater than 40 dB, of the LO and image spurious responses of superhet receivers with 10.7 MHz
IF. Murata’s advanced SAW design and fabrication technology is utilized to achieve high
performance and very low loss with simple external impedance matching.
433.92 MHz
SAW Filter
RF1172C
SM5050-8 Case
5 x 5
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
1. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 W test system with VSWR £ 1.2:1. The
test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, f
c
. Note that insertion loss and bandwidth and passband shape are dependent on
the impedance matching component values and quality.
2. The frequency f
c
is defined as the midpoint between the 3dB frequencies.
3. Where noted specifications apply over the entire specified operating temperature range.
4. The turnover temperature, T
O
, is the temperature of maximum (or turnover) frequency, f
o
. The nominal frequency at any case temperature, T
c
, may be calculated from:
f=f
o
[1 - FTC (T
o
-T
c
)
2
].
5. Frequency aging is the change in fc with time and is specified at +65°C or less. Aging may exceed the specification for prolonged temperatures above +65°C. Typically,
aging is greatest the first year after manufacture, decreasing significantly in subsequent years.
6. The design, manufacturing process, and specifications of this device are subject to change.
7. One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending.
Pb
Copyright © Murata Manufacturing Co., Ltd. All Rights Reserved 2003
