OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MPX2010D

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17
MPX2010
Rev 13, 10/2008
Freescale Semiconductor
© Freescale Semiconductor, Inc., 2005-2008. All rights reserved.
Pressure
+
10 kPa On-Chip Temperature
Compensated and Calibrated
Silicon Pressure Sensors
The MPX2010 series silicon piezoresistive pressure sensors provide a very
accurate and linear voltage output directly proportional to the applied pressure.
These sensors house a single monolithic silicon die with the strain gauge and
thin film resistor network integrated. The sensor is laser trimmed for precise
span, offset calibration and temperature compensation.
Features
• Temperature Compensated over 0°C to +85°C
• Ratiometric to Supply Voltage
• Differential and Gauge Options
• Available in Easy-to-Use Tape & Reel
ORDERING INFORMATION
Device Name
Package
Options
Case
No.
# of Ports Pressure Type
Device Marking
None Single Dual Gauge Differential Absolute
Small Outline Package (MPXV2010 Series)
MPXV2010GP
Tray 1369
• • MPXV2010GP
MPXV2010DP
Tray 1351
• • MPXV2010DP
Unibody Package (MPX2010 Series)
MPX2010D
Tray 344
• • MPX2010D
MPX2010DP
Tray 344C
• • MPX2010DP
MPX2010GP
Tray 344B
• • MPX2010GP
MPX2010GS
Tray 344E
• • MPX2010D
MPX2010GSX
Tray 344F
• • MPX2010D
MPAK Package (MPXM2010 Series)
MPXM2010D
Rail 1320
• • MPXM2010D
MPXM2010DT1
Tape and Reel 1320
• • MPXM2010D
MPXM2010GS
Rail 1320A
• • MPXM2010GS
MPXM2010GST1
Tape and Reel 1320A
• • MPXM2010GS
MPX2010
Series
0 to 10 kPa (0 to 1.45 psi)
25 mV Full Scale
(Typical)
Application Examples
• Respiratory Diagnostics
• Air Movement Control
• Controllers
• Pressure Switching
UNIBODY PACKAGES
SMALL OUTLINE PACKAGES
MPXV2010GP
CASE 1369-01
MPXV2010DP
CASE 1351-01
MPX2010D
CASE 344-15
MPX2010GP
CASE 344B-01
MPX2010DP
CASE 344C-01
MPX2010GS
CASE 344E-01
MPX2010GSX
CASE 344F-01
MPXM2010D/DT1
CASE 1320-02
MPXM2010GS/GST1
CASE 1320A-02
MPAK PACKAGES
MPX2010
Sensors
2 Freescale Semiconductor
Pressure
Operating Characteristics
Table 1. Operating Characteristics (V
S
= 10 V
DC
, T
A
= 25°C unless otherwise noted, P1 > P2)
Characteristic Symbol Min Typ Max Units
Pressure Range
(1)
1. 1.0 kPa (kiloPascal) equals 0.145 psi.
P
OP
0 — 10 kPa
Supply Voltage
(2)
2. Device is ratiometric within this specified excitation range. Operating the device at a different range may induce additional error due to device
self-heating.
V
S
— 10 16 V
DC
Supply Current
I
O
— 6.0 — mAdc
Full Scale Span
(3)
3. Full Scale Span (V
FSS
) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the
minimum rated pressure.
V
FSS
24 25 26 mV
Offset
(4)
4. Offset (V
OFF
) is defined as the output voltage at the minimum rated pressure.
V
OFF
–1.0 — 1.0 mV
Sensitivity
ΔV/ΔΡ — 2.5 — mV/kPa
Linearity
— –1.0 — 1.0 %V
FSS
Pressure Hysteresis (0 to 10 kPa)
— — ±0.1 — %V
FSS
Temperature Hysteresis (–40°C to +125°C)
— — ±0.5 — %V
FSS
Temperature Coefficient on Full Scale Span
TCV
FSS
–1.0 — 1.0 %V
FSS
Temperature Coefficient on Offset
TCV
OFF
–1.0 — 1.0 mV
Input Impedance
Z
IN
1300 — 2550 Ω
Output Impedance
Z
OUT
1400 — 3000 Ω
Response Time
(5)
(10% to 90%)
5. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a
specified step change in pressure.
t
R
—1.0—ms
Warm-Up Time
— — 20 — ms
Offset Stability
(6)
6. Offset stability is the product's output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test.
——±0.5 — %V
FSS
MPX2010
Sensors
Freescale Semiconductor 3
Pressure
Maximum Ratings
Voltage Output versus Applied Differential Pressure
The output voltage of the differential or gauge sensor
increases with increasing pressure applied to the pressure
side (P1) relative to the vacuum side (P2). Similarly, output
voltage increases as increasing vacuum is applied to the
vacuum side (P2) relative to the pressure side (P1).
Figure 1. shows a block diagram of the internal circuitry on
the stand-alone pressure sensor chip.
Figure 1. Temperature Compensated and Calibrated
Pressure Sensor Schematic
Table 2. Maximum Ratings
(1)
1. Exposure beyond the specified limits may cause permanent damage or degradation to the device.
Rating Symbol Value Unit
Maximum Pressure (P1 > P2)
P
MAX
75 kPa
Burst Pressure (P1 > P2)
P
BURST
100 kPa
Storage Temperature
T
STG
–40 to +125 °C
Operating Temperature
T
A
–40 to +125 °C
+V
OUT
–V
OUT
4
2
V
S
3
Sensing
Element
GND
1
Thin Film
Temperature
Compensation
and Calibration
Circuitry
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17

MPX2010D

Mfr. #:
Buy MPX2010D
Manufacturer:
NXP Semiconductors
Description:
Board Mount Pressure Sensors PRES SEN COMP 10KPA
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet