DESCO WEST: 3651 WALNUTAVE., CHINO, CA 91710 WEB SITE: www.desco.com
PHONE (909) 627-8178 FAX (909) 627-7449
DESCO EAST: 90 HUDSON RD, CANTON, MA 02021-1407
PHONE (781) 821-8370 FAX (781) 575-0172
DATE:
2/06
© 2006 DESCO INDUSTRIES INC.
Employee Owned
MATERIAL STATFREE S Plus
DRAWING PM-120
STATFREES Plus™ FLOOR MAT, VINYL, HOMOGENEOUS, ANTI-FATIGUE, .375" (9.5mm)
Description:
Statfree S Plus™ material is
specifically designed to reduce
fatigue in areas where standing is
required for long periods of time.
This floor mat combines a cross-link
vinyl/nitrile rubber construction
which is three times the resilience
of ordinary vinyl foam matting. The
extremely durable embossed
surface is safe for workers, and the
mat stays clean. Statfree S Plus™
meets the requirements of DOD-
HDBK-263, DOD-STD-2000,
ESD-S7.1 and EN 100 015 Issue 1.
Grey
Electrical Properties:
Property Test Method Value
RTG Resistance: ESD S7.1 <10
9
Ohms
RTT Resistance: ESD S7.1 <10
9
Ohms
Electrical Properties obtained by testing to industrial standards by an
independent testing laboratory @ 100 Volts and 50% relative humidity
unless otherwise specified. Complete text of the test report is available
upon request.
Specifications:
Construction: Vinyl/Nitrile Floor Funner. Designed
specifically to reduce fatigue as a standing
surface.
Thickness: 0.375 inches (9.5mm)
Texture:* Non-directional, heavy embossed, soil and
abrasion resistant
Color:* Grey
Weight: 0.65 lbs/ft
2
(0.317g/cm
2
)
Hardness: ASTM-D-2240-75 65 Shore “00”
Wear Resistance: Tabor Abrader, 1000 Cycles H-18 wheel, 1,000
grams load, negligible
Heat Resistance: -20°F to 140°F continuous
*Color and texture may vary between lots and mills
Grounding: This material must be properly grounded for optimum
electrical performance. Ask for Technical Bulleltin TB-2000 for mat
grounding instructions.
Cleaning: For optimum electrical performance, surface must be
cleaned regularly using an ESD mat cleaner. We suggest using our
Reztore™ Surface & Mat Cleaner Item #10435 or Static-Wipes
Item #10600. Do not use cleaners with silicone. Silicone buildup
will create an insulative film on the surface.
Disclaimer:
All statements, technical data, and recommendations contained herein are based
upon tests we believe to be reliable. However, the accuracy or completeness
thereof is not guaranteed. The proper and correct applications of products and
data is the responsibility of the user. Statements or recommendations not
contained herein shall have no force or effect unless embodied in a written
agreement signed by authorized offers of Desco Industries, Inc.
Matting materials have a tendency to shrink slightly
when first unrolled. In applications where length is
critical, allow the material to relax for at least 4 hours
before cutting to size. Always trim with a sharp knife
or razor blade.
Made in America
Hardware is not included with rolls.
Grounding Intervals for ESD Mats
Sufficient ground cords should be used to reliably meet
ANSI/ESD S20.20 Table 1 less than 1 x 10E9 ohms for
worksurfaces. An industry recommendation has been that
continuous runs of ESD matting should be grounded at ten-
foot intervals to allow proper charge decay rates with each
individual ESD mat should be grounded with ground snap
located no further than five feet from either end.
.375" (9.5mm)
THICK ROLLS
COLOR ITEM NO. APPROX. WT.
GREY 82066 130 lb.
Roll Stock Size 3' x 60'
(Roll Stock beveled on all sides)
Roll Stock Item Number
Limited Lifetime Warranty
Desco warrants for one year that Statfree
®
matting
products will be free of defects in materials and
workmanship and will guarantee dissipative/
conductive mat properties for the life of the mat.
Damage to matting caused by misuse of any kind,
including using inappropriate cleaners is not
covered by Desco Limited Warranty.
Tolerances:
Width ± .250"
Length ± .250" every 1 linear
foot of running material.
RoHS Compliance Statement
None of the following materials are intentionally added in
manufacturing this product: lead, mercury, cadmium,
hexavalent chromium, polybrominated biphenyls (PBB) or
polybrominated diphenyl ethers (PBDE) as outlined in the
Directive 2002/95/EC Article 4.1. See Desco Industries
Inc. letter on-line at Desco.com.
