VOL3120
www.vishay.com
Vishay Semiconductors
Rev. 1.5, 08-Jan-16
4
Document Number: 82656
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
• Minimum and maximum values were tested over recommended operating conditions (T
amb
= -40 °C to +100 °C, I
F(ON)
= 10 mA to 16 mA,
V
F(OFF)
= -3 V to 0.8 V, V
CC
= 15 V to 32 V, V
EE
= ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at T
amb
= 25 °C and with V
CC
- V
EE
= 32 V.
Fig. 4 - t
PLH
, t
PHL
, t
r
and t
f
Test Circuit and Waveforms
Note
• Minimum and maximum values were tested over recommended operating conditions (T
amb
= -40 °C to +100 °C, I
F(ON)
= 10 mA to 16 mA,
V
F(OFF)
= -3 V to 0.8 V, V
CC
= 15 V to 32 V, V
EE
= ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at T
amb
= 25 °C and with V
CC
- V
EE
= 32 V.
Fig. 5 - CMR Test Circuit and Waveforms
SWITCHING CHARACTERISTICS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Propagation delay time to logic low output R
g
= 10 Ω, C
g
= 10 nF, f = 10 kHz, duty cycle = 50 % t
PHL
0.1 0.25 0.5 µs
Propagation delay time to logic high output R
g
= 10 Ω, C
g
= 10 nF, f = 10 kHz, duty cycle = 50 % t
PLH
0.1 0.25 0.5 µs
Pulse width distortion R
g
= 10 Ω, C
g
= 10 nF, f = 10 kHz, duty cycle = 50 % PWD - - 0.3 µs
Rise time R
g
= 10 Ω, C
g
= 10 nF, f = 10 kHz, duty cycle = 50 % t
r
-0.1- µs
Fall time R
g
= 10 Ω, C
g
= 10 nF, f = 10 kHz, duty cycle = 50 % t
f
-0.1- µs
UVLO turn on delay V
O
> 5 V, I
F
= 10 mA T
UVLO-ON
-0.8- µs
UVLO turn off delay V
O
< 5 V, I
F
= 10 mA T
UVLO-OFF
-0.6- µs
COMMON MODE TRANSIENT IMMUNITY
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Common mode transient immunity at
logic high output
T
amb
= 25 °C, I
F
= 10 mA to 16 mA,
V
CM
= 1500 V, V
CC
= 32 V
|CM
H
|48 - - kV/µs
Common mode transient immunity at
logic low output
T
amb
= 25 °C, V
CM
= 1500 V,
V
CC
= 32 V, V
F
= 0 V
|CM
L
|48 - - kV/µs
I
F
t
r
t
PLH
t
PHL
OUT
90 %
50 %
10 %
t
f
0.1 µF
I
F
= 10 mA
to 16 mA
V
CC
= 15 V
to 32 V
10 Ω
500 Ω
10 kHz
50 %
duty cycle
V
O
10 nF
4
15
23
0 V
V
O
V
OH
V
OL
O
Switch at A: I
F
= 10 mA
Switch at B: I
F
= 0 mA
Δt
dV
dt
Δt
V
CM
=
V
CM
5 V
A
R
B
0.1 µF
V
CC
= 32 V
V
O
4
15
23
V
CM
= 1500 V
I
F
