OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

BLM18AG102SN1D

P1-P3P4-P6P7-P9P10-P12
Spec. No. JENF243A-0003AA-01 P.4/12
MURATA MFG.CO., LTD.
Reference Only
:Elect
r
ode
1.6±0.15
0.8±0.15
0.4
±0.2
T
•
Operating Temperature : -55°C to +125°C • Storage Temperature : -55°C to +125°C
(*1)In case of Rated current is more than 1A,
Rated Current is derated as right figure
depending on the operating temperature.
4.Style and Dimensions
■ Equivalent Circuit
(in mm)
5.Marking
No marking.
6.Standard Testing Conditions
< Unless otherwise specified > < In case of doubt >
Temperature : Ordinary Temp. (15 °C to 35 °C ) Temperature : 20°C±2 °C
Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH)
Atmospheric pressure : 86kPa to 106kPa
7.Specifications
7-1.Electrical Performance
No. Item Specification Test Method
7-1-1 Impedance Meet item 3.
Measuring Frequency : 100MHz±1MHz
Measuring Equipment : KEYSIGHT 4291A or the equivalent
Test Fixture : KEYSIGHT 16192A or the equivalent
7-1-2 DC
Resistance
Meet item 3. Measuring Equipment : Digital multi meter
For BLM18SN_TN
Measuring Equipment : YOKOGAWA 755611 or the equivalent
Test Fixture : KEYSIGHT 16044A or the equivalent
＊Except resistance of the Substrate and Wire
BLM18SG***TN1* 0.5±0.15
BLM18SN***TN1* 0.6±0.15
BLM18TG***TN1* 0.6±0.1
BLM18KG***TN1* 0.6±0.15
BLM18*****SN1* 0.8±0.15
Resistance element becomes
dominant at high frequencies.
()
■ Unit Mass (Typical value)
BLM18*****SN1*:0.005g
BLM18*****TN1*:0.004g
Operating Temperature (°C)
85 125
0
Rated Current (A)
at 85°C
Rated current
at 125°C
Rated current
Spec. No. JENF243A-0003AA-01 P.5/12
MURATA MFG.CO., LTD.
Reference Only
7-2.Mechanical Performance
No. Item Specification Test Method
7-2-1 Appearance
and
Dimensions
Meet item 4. Visual Inspection and measured with Slide Calipers.
7-2-2 Bonding
Strength
Meet Table 1.
Table 1
It shall be soldered on the substrate.
Applying Force(F) : 6.8N
Applying Time : 5s±1s
Applied direction :Parallel to substrate
7-2-3 Bending
Strength
It shall be soldered on the substrate.
Substrate: Glass-epoxy 100mm×40mm×1.6mm
Deflection : 1.0mm
Speed of Applying Force : 0.5mm/s
Keeping Time : 30s
7-2-4 Vibration It shall be soldered on the substrate.
Oscillation Frequency : 10Hz to 55Hz to 10Hz for 1 min
Total Amplitude : 1.5mm
Testing Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 h)
7-2-5 Resistance
to Soldering
Heat
Meet Table 2.
Table 2
Appearance No damage
Impedance
Change
(at 100MHz)
Within ±30%
(for BLM18KG
Within ±40%)
(for BLM18SN
Within ±50%)
DC
Resistance
Meet item 3.
Pre-Heating : 150°C±10°C, 60s～90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 270°C±5°C
Immersion Time : 10s±0.5s
Immersion and emersion rates : 25mm/s
Then measured after exposure in the room condition for 48h±4h.
7-2-6 Drop Products shall be no failure
after tested.
It shall be dropped on concrete or steel board.
Method : free fall
Height : 75cm
Attitude from which the product is dropped : 3 direction
The number of times : 3 times for each direction(Total 9 times)
7-2-7 Solderability The electrodes shall be at
least 95% covered with new
solder coating.
Flux : Ethanol solution of rosin,25(wt)%
Pre-Heating : 150°C±10°C, 60s～90s
Solder : Sn-3.0Ag-0.5Cu
Solder Temperature : 240°C±5°C
Immersion Time : 3s±1s
Immersion and emersion rates : 25mm/s
Appearance No damage
Impedance
Change
(at 100MHz)
Within ±30%
(for BLM18SN
W
ithin ±50%)
DC
Resistance
Meet item 3.
45mm
R340
F
Deflection
45mm
Product
Pressure jig
R0.5
Ｆ
Substrate
Ｆ
Side view
Spec. No. JENF243A-0003AA-01 P.6/12
MURATA MFG.CO., LTD.
Reference Only
7-3.Environmental Performance
It shall be soldered on the substrate.
No. Item Specification Test Method
7-3-1 Temperature
Cycle
Meet Table 3.
Table 3
Appearance No damage
Impedance
Change
(at 100MHz)
Within ±30%
(for BLM18KG
Within-10%to
+50%)
(for BLM18SN
Within ±50%)
DC
Resistance
Meet item 3.
1 cycle:
1 step:-55 °C(+0 °C,-3 °C) / 30min±3min
2 step:Ordinary temp. / 10min to 15min
3 step:+125 °C(+3 °C,-0 °C) / 30min±3min
4 step: Ordinary temp. / 10min to 15min
Total of 100 cycles
Then measured after exposure in the room condition for 48h±4h.
7-3-2 Humidity Meet Table 1. Temperature : 40°C±2°C
Humidity : 90%(RH) to 95%(RH)
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for 48h±4h.
7-3-3 Heat Life Temperature : 125°C±3°C
(in case of Rated current is more than 1A,
do the test at : +85 °C±3°C)
Applying Current : Rated Current
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for 48h±4h.
7-3-4 Cold
Resistance
Temperature : -55±2°C
Time : 1000h(+48h,-0h)
Then measured after exposure in the room condition for 48h±4h.
P1-P3P4-P6P7-P9P10-P12

BLM18AG102SN1D

Mfr. #:
Buy BLM18AG102SN1D
Manufacturer:
Description:
EMI Filter Beads, Chips & Arrays 0603 1000 OHM
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet