5
FN6356.4
November 22, 2008
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V+ = +3.6V, V
IN
= 0V or V+ 25 0.01 µA
Full 0.52 µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
25 0.5 V
Input Voltage High, V
INH
25 1.4 V
Input Current, I
INH
, I
INL
V+ = 3.3V, V
IN
= 0V or V+ (Note 9) Full -0.5 0.5 µA
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 4),
Unless Otherwise Specified.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 5, 8) TYP
MAX
(Notes 5, 8) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 V+ V
ON-Resistance, r
ON
V+ = 1.65V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+
(see Figure 5)
25 0.7 0.8 Ω
Full 0.85 Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(see Figure 1)
25 70 ns
Full 80 ns
Turn-OFF Time, t
OFF
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(see Figure 1)
25 54 ns
Full 65 ns
Break-Before-Make Time Delay, t
d
V+ = 2.0V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(see Figure 3)
Full 10 ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω (see Figure 2) 25 42 pC
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (see Figure 7) 25 70 pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (see Figure 7) 25 186 pF
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
25 0.4 V
Input Voltage High, V
INH
25 1.0 V
Input Current, I
INH
, I
INL
V+ = 2.0V, V
IN
= 0V or V+ (Note 9) Full -0.5 0.5 µA
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
7. r
ON
matching between channels is calculated by subtracting the channel with the highest max r
ON
value from the channel with lowest max r
ON
value, between NC1 and NC2 or between NO1 and NO2.
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
9. Limits established by characterization and are not production tested.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 4),
Unless Otherwise Specified. (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 5, 8) TYP
MAX
(Notes 5, 8) UNITS
ISL54050
