5
FN7111.4
May 4, 2007
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Absolute Maximum Ratings (T
A
= +25°C) Thermal Information
Supply Voltage Between V
S
+ and V
S
-. . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . V
S
- -0.5V, V
S
+0.5V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA
ESD Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2kV
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications V
S
+
= +5V, V
S
-
= -5V, R
L
= 10k, C
L
= 10pF to 0V, T
A
= +25°C, Unless Otherwise Specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage V
CM
= 0V 1 15 mV
TCV
OS
Average Offset Voltage Drift (Note 1) 5 µV/°C
I
B
Input Bias Current V
CM
= 0V 2 50 nA
R
IN
Input Impedance 1G
C
IN
Input Capacitance 1.35 pF
A
V
Voltage Gain -4.5V V
OUT
4.5V 0.99 1.01 V/V
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low I
L
= -5mA -4.95 -4.85 V
V
OH
Output Swing High I
L
= +5mA 4.85 4.95 V
I
OUT
(max) Max Output Current (Note 2) R
L
= 10 100 ±120 mA
POWER SUPPLY PERFORMANCE
PSRR Power Supply Rejection Ratio V
S
is moved from ±2.25V to ±7.75V 55 80 dB
I
S
Supply Current No load (EL5127) 0.7 0.9 mA
No load (EL5227) 1.2 1.4 mA
No load (EL5327) 1.4 2 mA
No load (EL5427) 1.6 2.2 mA
DYNAMIC PERFORMANCE
SR Slew Rate (Note 3) -4.0V V
OUT
4.0V, 20% to 80% 0.9 2.2 V/µs
t
S
Settling to +0.1% (A
V
= +1) (A
V
= +1), V
O
= 2V step 900 ns
BW -3dB Bandwidth R
L
= 10k, C
L
= 10pF 2.5 MHz
CS Channel Separation f = 100kHz 75 dB
NOTES:
1. Measured over operating temperature range.
2. Instantaneous peak current.
3. Slew rate is measured on rising and falling edges.
EL5127, EL5227, EL5327, EL5427