E6C3-C
2
Ratings and Specifications
*1. An inrush current of approximately 9 A will flow for approximately 0.1 ms when the power is turned ON.
*2. Complementary Output
The complementary output has two output
transistors (NPN and PNP) as shown below. These
two output transistors alternately turn ON and OFF
depending on the high or low output signal. When
using them, pull up to the positive power supply
voltage level or pull down to 0 V. The
complementary output allows flow-in or flow-out of
the output current and thus the rising and falling
speeds of signals are fast. This allows a long cable
distance. They can be connected to open-collector
input devices (NPN, PNP).
*3. The line driver output is a data transmission circuit compatible with RS-422A and long-distance transmission is possible with a twisted-pair cable. (AM26LS31
equivalent)
*4. The maximum electrical response speed is determined by the resolution and maximum response frequency as follows:
Maximum electrical response speed (rpm) = × 60
This means that the Rotary Encoder will not operate electrically if its speed exceeds the maximum electrical response speed.
*5. The phase Z signal is output when cut face D on the shaft and the cable connection direction are as shown in the following diagram (output position range: ±15°).
Item Model E6C3-CWZ5GH E6C3-CWZ3EH E6C3-CWZ3XH
Power supply voltage
12 VDC −10% to 24 VDC +15%,
ripple (p-p): 5% max.
5 VDC −5% to 12 VDC +10%,
ripple (p-p): 5% max.
Current consumption*1 100 mA max.
Resolution (pulses/rotation) 100, 200, 300, 360, 500, 600, 720, 800, 1,000, 1,024, 1,200, 1,500, 1,800, 2,000, 2,048, 2,500, 3,600
Output phases Phases A, B, and Z*5 Phases A, A, B, B, Z, and Z
Output configuration Complementary outputs*2 Voltage output (NPN output) Line driver output*3
Output capacity
Output voltage: VH = Vcc = 3 V min.
(IO = 30 mA)
VL = 2 V max.
(IO = −30 mA)
Output current: ±30 mA
Output resistance: 2 kΩ
Output current: 35 mA max.
Residual voltage: 0.7 V max.
AM26LS31 equivalent
Output current: High level: IO = −10 mA
Low level: IS = 10 mA
Output voltage: VO = 2.5 V min.
VS = 0.5 V max.
Maximum response
frequency*4
125 kHz (65 kHz when using phase Z reset)
Phase difference between
outputs
90°±45° between A and B (1/4 T ± 1/8 T)
Rise and fall times of output
1 μs max.
(Cable length: 2 m, Output current: 30 mA)
1 μs max.
(Cable length: 2 m, Output current: 35
mA)
1 μs max.
(Cable length: 2 m, IO: −10 mA,
IS: 10 mA)
Starting torque 10 mN·m max. at room temperature, 30 mN·m max. at low temperature
Moment of inertia 2.0 × 10
−6
kg·m
2
max.; 1.9 × 10
−6
kg·m
2
max. at 500 P/R max.
Shaft loading
Radial 80 N
Thrust 50 N
Maximum permissible speed 5,000 r/min
Protection circuits Output load short-circuit protection ---
Ambient temperature range Operating: −10 to 70°C (with no icing), Storage: −25 to 85°C (with no icing)
Ambient humidity range Operating/Storage: 35% to 85% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 500 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 500 Hz, 150 m/s
2
or 2-mm double amplitude for 11 min 3 times each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s
2
3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP65, in-house standards: oilproof
Connection method Pre-wired Models (Standard cable length: 1 m)
Material Case: Aluminum, Main unit: Aluminum, Shaft: SUS303
Weight (packed state) Approx. 300 g
Accessories Instruction manual Note: Coupling, mounting bracket and hex-head spanner are sold separately.
0 V
OUT
PNP
transistor
NPN
transistor
Power
supply
E6C3-CWZ5GH
Signal
Maximum response frequency
Resolution
120˚
120˚
40 dia.
Cut face D