OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HCTE-0375-0-SP-CS7063

P1-P3P4-P6P7-P9P10-P11
If this document is printed it becomes uncontrolled. Check f
or the latest revision.
Tyco Electronics Corporation
300 Constitutional Drive
Menlo Park, CA 94025 USA
Specification
This Issue:
Date:
Replaces:
RT-1162
Issue 7
November 19, 1997
Issue 6
HELICAL CONVOLEX
®
TUBING
HCTE
Ethylene Tetrafluoroethylene, Modified, Radiation-Crosslinked
1. SCOPE
This specification covers the requirements for one type of convoluted tubing that will provide mechanical
protection for electrical wiring systems.
2. APPLICABLE DOCUMENTS
This specification takes precedence over documents referenced herein. Unless otherwise specified, the latest
issue of referenced documents applies. The following documents form a part of this specification to the
extent specified herein.
2.1 GOVERNMENT-FURNISHED DOCUMENTS
Military
MIL-L-2104 Lubricating Oil, Internal Combustion Engine, Heavy Duty
MIL-G-3056 Gasoline, Automotive, Combat
MIL-H-5606 Hydraulic Fluid, Petroleum Base, Aircraft, Missile and Ordnance
MIL-T-5624 Turbine Fuel, Aviation Grade JP-4, JP-5 and JP5/JP8
MIL-L-7808 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base
MIL-A-8243 Anti-Icing and Deicing - Defrosting Fluid
MIL-L-23699 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base
MIL-C-43616 Cleaning Compound, Aircraft Surface
MIL-F-46162 Fuel, Diesel, Referee Grade
MIL-L-46167 Lubricating Oil, Internal Combustion Engine, Arctic
MIL-H-46170 Hydraulic Fluid, Rust Inhibited, Fire Resistance Synthetic Hydrocarbon Base
MIL-T-81914 Tubing, Plastic, Flexible, Convoluted, Conduit, General Specification for
Federal
O-S-1926 Sodium Chloride 5% Solution
PC-437 Cleaning compound, High Pressure (Steam Cleaner)
VV-F-800 Fuel Oil, Diesel
Page 2 SPECIFICATION RT 1162- ISSUE 7
If this document is printed it becomes uncontrolled. Check f
or the latest revision.
2.2 OTHER PUBLICATIONS
American Society for Testing and Materials (ASTM)
ASTM D 638 Standard Test Methods for Tensile Properties of Plastics
ASTM D 792 Standard Test Methods for Specific Gravity and Density of Plastics by Displacement
ASTM D 876 Standard Methods of Testing Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical
Insulation
ASTM D 910 Standard Specification for Aviation Gasoline
ASTM D 3032 Standard Methods of Testing Hookup Wire Insulation.
ASTM G 21 Recommended Practice for Determining Resistance of Synthetic Polymeric Materials to
Fungi
Copies of ASTM publications may be obtained from the American Society for Testing and Materials, 1916
Race Street, Philadelphia, Pennsylvania 19103.
3. REQUIREMENTS
3.1 MATERIAL
The tubing material shall be modified ethylene tetrafluoroethylene, radiation crosslinked. It shall be
homogeneous and essentially free from flaws, defects, pinholes, cracks, and inclusions.
3.2 COLOR
The tubing shall be black.
3.3 PROPERTIES
The tubing shall meet the requirements of Table 3.
4. QUALITY ASSURANCE PROVISIONS
4.1 CLASSIFICATION OF TESTS
4.1.1 Qualification Tests
Qualification tests are those performed on samples submitted for qualification as representative of standard
product and shall consist of all tests listed in this specification.
4.1.2 Acceptance Tests
Acceptance tests are those performed on tubing submitted for acceptance under contract. Acceptance tests
shall consist of the following:
Dimensions
Tensile Strength
Extensibility
Crush Resistance
Flammability
Heat Shock
Longitudinal Change
SPECIFICATION RT 1162- ISSUE 7 Page 3
If this document is printed it becomes uncontrolled. Check f
or the latest revision.
4.2 SAMPLING INSTRUCTIONS
4.2.1 Qualification Test Samples
Qualification test samples shall consist of sufficient lengths of Sizes 0500 and 1500. These two sizes will
qualify all sizes as follows. For Fluid Resistance, one size shall qualify all sizes.
Qualification Size Qualification Range
0500 Below 1000
1500 1000 and above
4.2.2 Acceptance Test Samples
Acceptance test samples shall consist of not less than 10 feet (3 m) of tubing selected at random from each
lot. A lot shall consist of all tubing of the same size, from the same production run, and offered for
inspection at the same time.
4.3 TEST PROCEDURES
4.3.1 Tensile Properties (Tensile Strength & Extensibility)
Test three 6-inch (150-mm) specimens of tubing, [cut 6 x 1/2 inch (150 x 12 mm) strips from tubing larger
than Size 0437], in accordance with ASTM D 638, using an initial jaw separation of 3 inches (76 mm), 2-inch
(50-mm) bench marks and a 2-inch (50-mm) per minute rate of jaw separation. Measure the benchmark
separation and load at break. Report these values as the extensibility and tensile strength, respectively.
4.3.2 Crush Resistance
Cut three specimens of tubing to provide the number of convolutions specified in Table 1. Place each
specimen horizontally between plates larger than 2 inches (50 mm) square in a standard tensile testing
machine that is arranged to measure and record compressive force. Operate the machine at a compressive
speed of 0.2 inches (5 mm) per minute. Measure the average force required to reduce the outside diameter of
the tubing by 25 percent and report this force as the crush resistance.
P1-P3P4-P6P7-P9P10-P11

HCTE-0375-0-SP-CS7063

Mfr. #:
Buy HCTE-0375-0-SP-CS7063
Manufacturer:
Raychem / TE Connectivity
Description:
Spiral Wraps, Sleeves, Tubing & Conduit HCTE-0375-0SP-CS7063 PRICED PER FOOT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet