SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
Note.6
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING HUMIDITY
WORKING TEMP.
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
OVER TEMPERATURE
Note.5
AC CURRENT (Typ.)
1800ms, 20ms/230VAC 1800ms, 20ms/115VAC at full load
100ms/230VAC 24ms/115VAC at full load
85 ~ 264VAC 120 ~ 370VDC
47 ~ 440Hz
74%66%
13.8 ~ 16.2V
79%
17.25 ~ 20.25V
79%
27.6 ~ 32.4V
0.25A/115VAC 0.15A/230VAC
COLD START 25A/115VAC 45A/230VAC
Above 105% rated output power
5.75 ~ 6.75V3.8 ~ 4.95V
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
I/P-O/P:4KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
20 ~ 90% RH non-condensing
-20 ~ +70 (Refer to "Derating Curve")℃
-40 ~ +85 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
723.2Khrs min. MIL-HDBK-217F (25 )℃
65*45*22mm (L*W*H)
0.045Kg; 120pcs/6.4Kg/0.97CUFT
File Name:NFM-10-SPEC 2018-01-12
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±0.5%
±1.0%
±1.0%
±1.0%
±1.0%
150mVp-p150mVp-p 150mVp-p 150mVp-p 240mVp-p
5V3.3V 15V
2A2.5A 0.67A 0.42A
0 ~ 2A0 ~ 2.5A 0 ~ 0.85A 0 ~ 0.67A 0 ~ 0.42A
10W8.25W 10.2W 10.05W 10.08W
NFM-10-5 NFM-10-12 NFM-10-15 NFM-10-24NFM-10-3.3
SAFETY STANDARDS
NFM-10 series
■ Features :
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. The over temperature protection (OTP) is the built-in function of the control IC (U1). The activating level described above is based on the specification
provided by the IC manufacturer.
6. .Touch current was measured from primary input to DC output
7. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
Tj 140 typically (U1) detect on main control IC℃
Protection type : Shut off o/p voltage, clamping by zener diode
10.8 ~ 13.2V 13.5 ~ 16.5V 21.6 ~ 26.4V4.5 ~ 5.5V3 ~ 3.63V
Compliance to EN55011(CISPR11), EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61204-3, medical level, criteria A, EAC TP TC 020
ANSI/AAMI ES60601-1,TUV EN60601-1, IEC60601-1 approved
, EAC TP TC 004
Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage / Over temperature
Ultra-miniature size, light weight
Cooling by free air convection
Isolation classⅡ
Medical safety approved (2 x MOPP between primary to secondary)
No load power consumption<0.5W
100% full load burn-in test
Fixed switching frequency at 67KHz
High reliability
Suitable for BF application with appropriate system consideration
3 years warranty
±2.0%
±2.0%
±1.0% ±1.0%
78%
12V
0.85A
±1.0%
24V
EMC IMMUNITY
EMC EMISSION
Touch current < 80 A/264VAC
μ
ISOLATION LEVEL
Primary-Secondary: 2xMOPP
10W Single Output Medical Grade Switching Power Supply
EN 60601-1
IEC 60601-1
8
