United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com2/6
KMQ
SNAP MOUNT-105C
KMQ Series
KMQ Specifications
Item
Category Temperature Range
25 to
105C
Rated Voltage Range 160 to 450VDC
Capacitance Range 68 to 3,300F
Capacitance Tolerance
20% (M ) at
20C, 120Hz
Leakage Current I ≤ 3 CV (A) after 5 minutes at
20C.
Where I = Max. leakage current (A), C = Nominal capacitance (F ) and V = Rated voltage ( V)
Characteristics
Rated Voltage (V)
Tan (DF)
160-250
0.15 max.
315 - 400
0.15 max.
450
0.20 max.
Dissipation Factor (Tan )At
20C, 120Hz
Rated Voltage (V)
Z(
25C)/Z(
20C)
160-250
4
315 - 400
8
450
8
Low Temperature
Characteristics
At 120Hz, impedance (Z ) ratio between the
25C value and
20C value shall not exceed
the values given below.
Rated Ripple Current Multipliers
Refer to Section 4 of the
Mini-Glossary for explanation of
Rated Ripple Current Multipliers.
Frequency (Hz )
DC Rated Voltage
160-250V
315-450V
50Hz
0.81
0.77
120Hz
1.00
1.00
300Hz
1.17
1.16
1kHz
1.32
1.30
10kHz
1.45
1.41
50kHz
1.50
1.43
Shelf Life The following specifications shall be satisfied when the capacitors are restored to
20C after
exposing them for 1,000 hours at
105C without voltage applied. The rated voltage shall be
applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than
48 hours before the measurements.
Capacitance change: ≤
15% of initial measured value
Tan (DF) : ≤ 150% of initial specified value
Leakage current : ≤ initial specified value
Endurance
(Load Life)
The following specifications shall be satisfied when the capacitors are restored to
20C after
subjecting them to DC voltage for 2,000 hours at
105C with the rated ripple current applied.
The sum of the DC voltage and peak AC voltage must not exceed the full rated voltage of
the capacitors.
Capacitance change: ≤
20% of initial measured value
Tan (DF) : ≤ 200% of initial specified value
Leakage current : ≤ initial specified value
Terminal Code: T2 = 2- Pin Snap-in (Standard ).
Case Code: See Case Sizes in Tables.
Capacitance Tolerance: M =
20%
Capacitance Value: Expressed in Microfarads. The first two digits are
significant figures, and the third digit indicates the number of zeros
for capacitance of 100F or more. R indicates the decimal point for
capacitance less than 100F (e.g. R15 = .15F; 1R5 = 1.5F;
15R = 15F; 151= 150F; 152 = 1,500F; 153 = 15,000F).
Lead Configuration: VS = 2-Pin Snap-in Terminals.
DC Rated Voltage: Expressed in Volts (e.g.180 = 180WVDC).
Series Name: Indicates Basic Capacitor Design.
Part Numbering System for KMQ Series When ordering, always specify complete catalog number for KMQ Series.
KMQ 180 VS 152 M 35X30 T2
Engineering Bulletin Jul 03