Reference only
ESRCE01C
15 / 19
No.
AEC-Q200
Test Item
Specifications AEC-Q200 Test Method
15 ESD
Appearance
No defects or abnormalities
Per AEC-Q200-002
Capacitance
Within the specified tolerance
D.F.
0.025 max.
I.R.
More than 10,000M or 500 MF
(Whichever is smaller)
16 Solderability Lead wire should be soldered with uniform coating on
the axial direction over 95% of the circumferential
direction.
Should be placed into steam aging for 8h15 min.
The terminal of capacitor is dipped into a solution of ethanol
(JIS K 8101) and rosin (JIS K 5902) (25% rosin in weight
propotion).Immerse in solder solution for 20.5 seconds.
In both cases the depth of dipping is up to about 1.5 to 2mm from
the terminal body.
Temp. of solder :
2455C Lead Free Solder(Sn-3.0Ag-0.5Cu)
2355C H60A or H63A Eutectic Solder
17 Electrical
Characte-
rization
Apperance
No defects or abnormalities
Visual inspection.
Capacitance
Within the specified tolerance
The capacitance/D.F. should be measured at 25C at the
frequency and voltage shown in the table.
D.F.
0.025 max.
I.R.
Between
Terminals
10,000M or 500MF min.
(Whichever is smaller)
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at 25 C within 2 min. of charging.
Dielectric
Strength
Between
Terminals
No defects or abnormalities
The capacitor should not be damaged when DC voltage of 250%
of the rated voltage is applied between the terminations for 1 to 5
seconds.
(Charge/Discharge current 50mA.)
Body
Insulation
No defects or abnormalities
The capacitor is placed in a container with metal balls of 1mm
diameter so that each terminal, short-circuit is kept approximately
2mm from the balls, and 250% of the rated DC voltage is
impressed for 1 to 5 seconds between capacitor terminals and
metal balls.
(Charge/Discharge current 50mA.)
18 Terminal
Strength
Tensile
Strength
Termination not to be broken or loosened As in the figure, fix the capacitor body, apply the force gradually
to each lead in the radial direction of the capacitor until reaching
10N and then keep the force applied for 101 seconds.
Bending
Strength
Termination not to be broken or loosened Each lead wire should be subjected to a force of 2.5N and then
be bent 90° at the point of egress in one direction. Each wire is
then returned to the original position and bent 90° in the opposite
direction at the rate of one bend per 2 to 3 seconds.
19 Capacitance
Temperature
Characteristics
Char.X7R: Within ±15%
Char.X7S: Within ±22%
The capacitance change should be measured after 5min. at
each specified temperature step.
The ranges of capacitance change compared with the above
25°C value over the temperature ranges shown in the table
should be within the specified ranges.
•Pretreatment
Perform the heat treatment at 150+0/-10°C for 60±5 min and
then let sit for 24±2 h at *room condition.
Perform the initial measurement.
* “room condition” Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
Step Temperature(C)
1 252
2 -553
3 252
4 1253
5 252
F
Frequency Voltage
10.1kHz 10 . 2 V ( r.m.s.)
