RPM960-H14E3A

RPM960-H14
Photo Link Module
Rev.C 4/5
zElectrical characteristics (Unless otherwise noted, V
CC
=3V, LEDV
CC
=3V, V
IO
=3V, Ta=25°C)
Parameter Symbol Min.
Typ. Max. Unit
Conditions
Consumption current 1 I
CC
1
I
CC
2
VPDH
VPDL
IPDH
IPDL
440
µA
PWDOWN=OV, At no input light
PWDOWN=V
IO, At no input light
PWDOWN=V
IO
V
IO = 1.8 to 3.6 V
Consumption current 2
Transmission rate
PWDOWN input high voltage
PWDOWN input low voltage
PWDOWN input high current
PWDOWN input low current
TXD input high voltage
TXD input low voltage
RXD output high voltage
RXD output rise time
RXD output fall time
RXD output pulse width
Receiver latency time
RXD output low voltage
TXD input high current
TXD input low current
LED anode current 1
270
0.01
0
2.4
2/3V
IO
2/3VIO
1/3VIO
1/3VIO
10
610
µA
0.2
kbps1152
V
V
V
IO
< Transmitter >
< Receiver >
VTXH
VTXL
ITXH
ITXL
ILED1
VRXH
VRXL
tRR
tFR
tRT
twRXD
PWDOWN=0V
TXD=V
IO
TXD=0 V
0
1.0
0
2.5
1.0
0
228
V
IO0.4
0
1.0
5
0
170
20
20
380
100
µA
1.0
µA
1.0
V
V
µA
µA
mA
V
V
ns
ns
µs
ns
V
IO
1.0
400
V
IO
0.4
532
200
IRXH=
200µA
IRXL=
200µA
C
L=15pF
C
L=15pF
C
L=15pF, 2.4k to 1.152 Mbps
VIO
=
1.8 to 3.6 V
(VIO VCC)
mA
(V
IO VCC)
LED anode current 2 ILED2 180 260
R1=5.6
R1=5.6
LEDV
CC=5.5V
ns 1.152 Mbps160
−−
TjrxdRXD output pulse edge jitter
<
<
zOptical characteristics (Unless otherwise noted, V
CC
=3V, LEDV
CC
=3V, V
IO
=3V, Ta=25°C)
1. This product is not designed for protection against radioactive rays.
2. This product dose not include laser transmitter.
3. This product includes one PIN photo diode.
4. This product dose not include optical load.
Parameter
Symbol Min. Typ. Max. Unit
Conditions
Peak wave length
λP
IE1
θD / 2
TLEDmax
Tr / Tf
Tj
Eemin
870 nm
15 deg θ L 15 deg
TXD=V
IO
10% to 90%
Intensity1
Rise time / Fall time
Optical over shoot
Edge jitter
Minimum irradiance in angular
Input halfangle
Maximum emitting time
850
6325
±18
900
mW / Sr200
mW / cm
2
deg
ns
deg
µs
120
9
±15
16
%25
ns40
500
14
R1=5.6
Halfangle
θL / 2
25
25
Maximum irradiance in augular Eemax
µW / cm
2
−−
48
Optical pulse width Twe 172 217 256 ns
tTXD=217 ns
15 deg θ L 15 deg
15 deg θ L 15 deg
<
<
<
<
<
<
RPM960-H14
Photo Link Module
Rev.C 5/5
zNotes
1) LEDV
CC
(1pin), V
CC
(6pin) and V
IO
(7pin)
Other power source can be used difference between LEDV
CC
and V
CC
and V
IO
. (V
IO
< V
CC
+0.3V)
2) Caution in designing board lay-out
To get maximum potential from RPM960-H14, please keep in mind following instruction.
The line of RXD (4pin) should be connected at backside via through hole close to RPM960-H14 pin lead. Better not
to be close to photo diode side (8pin side).
This is to minimize feedback supplied to photo diode from RXD.
Better to be placed at more than 1.0cm radius from photo diode (8pin side) and also away from the parts which
generate noise, such as DC / DC converter.
As for C1 between 6 and 8 pins, it should be placed close to RPM960-H14.
3) Notes
Please be sure to set up the TXD (3pin) input to be “L” (under 0.6V) except transmitting data.
(For < 90µ sec. ON duty < 25%).
Powerdown current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode.
Please use by the signal format which is specified by IrDA Ver1.3 (Low Power) except 4 Mbps.
There might be on error if used by different signal format.
4) Eye safe
EN60825-1 (IEC60825-1 amendment2), Class1 Eye safe.
zExternal dimensions (Unit : mm)
2.COPLANARITY : 0.1mmMAX
1.TOLERANCE : ±0.2mm
A
UNIT : mm
NOTE
ETH396
PinPD
LED
81
2.67
0.75
2.2
R1.0
R1.1
2.9
0.68±0.1
0.6±0.1
0.95
P0.95×7=6.65
(0.13)
2.59
0.37±0.1
4.0
1.4
1.1
2.2
0.78
0.15±0.1
0.76
0.15±0.1
1.0
8.0
2.8
0.48
0.6
2.2
A Part Size (Shield Case underside size)
Appendix
Appendix1-Rev1.1
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.

RPM960-H14E3A

Mfr. #:
Manufacturer:
Description:
Fiber Optic Transmitters, Receivers, Transceivers IRDA IR COMM SIDE VIEW W/SHIELD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet