PCD-60-500B PCD-60-700B PCD-60-1050B PCD-60-1400B PCD-60-1750B PCD-60-2000B PCD-60-2400B
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
SPECIFICATION
MODEL
RATED CURRENT
CURRENT ACCURACY
OPERATING VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
SHORT CIRCUIT
OVER TEMPERATURE
1400mA 1750mA 2000mA 2400mA1050mA700mA500mA
60.2W 59.5W 60W 60W59.85W60.2W54W
3.4Vp-p 3.3Vp-p 2.4Vp-p 2.4Vp-p3.8Vp-p5.6Vp-p10.2Vp-p
PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
47 ~ 63Hz
85% 85% 85% 84%86%86%
87%
0.6A/230VAC 0.5A/277VAC
COLD START 13A at 230VAC(twidth=50 s measured at 50% Ipeak)μ
<0.5mA / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
-30 ~ +45 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
358.030Khrs min. MIL-HDBK-217F (25 )℃
128*60*31.5mm (L*W*H)
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
3. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
4. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft)℃℃ .
0.35Kg;30pcs/11.5Kg/0.58CUFT
60W Single OutputAC Dimmable LED Power Supply
AC phase-cut dimming
Work with leading edge and trailing edge TRIAC dimmers
Built-in active PFC function
Constant current design
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
IP42 design
ⅡClass power unit, no FG
Suitable for LED related fixture or appliance
(such as LED Decoration or Advertisement devices)
100% full load burn-in test
Low cost
High reliability
3 years warranty
■
Features :
PCD-60 series
RIPPLE & NOISE (max.) Note.1
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, auto-recovery
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
Compliance to EN55015, EN61000-3-2 Class C ; EN61000-3-3 EAC TP TC 020
,
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level(Surge 2KV), criteria B EAC TP TC 020,
ENEC EN61347-1, EN61347-2-13 independent, EN62384, EAC TP TC 004,IP42 approved
50 ~ 86V70 ~ 108V 25 ~ 43V 20 ~ 34V 18 ~ 30V 15 ~ 25V34 ~ 57V
File Name:PCD-60-SPEC 2018-05-02
100V118V 63V 50V 50V 35V 35V
NO LOAD OUTPUT VOLTAGE (max.)
EMC IMMUNITY
EMC EMISSION
±5.0%
VOLTAGE RANGE 180~295VAC
TOTAL HARMONIC DISTORTION
THD< 20% when output loading 60%(PCD-60-500B loading 65%)at 230VAC input and output loading 75% at 277VAC input≧≧ ≧
IP42
SELV
110
MM
500ms / 230VAC at full load
