PF1262-0R02J2

Riedon Inc. 300 Cypress Avenue Alhambra CA 91801 (626) 284-9901 (626) 284-1704
www.riedon.com
08/14
PF1262 Series
TO-126 Housing
Resistances from 0.01 to 51K Ohms
Rated Power to 20 Watts
Resistance Tolerances to ±1%
TCR to ±50ppm/°C
Low Inductance ( <50nH )
Isolated Back Plate
SPECIFICATIONS
Part Description: Part Type - Resistance - Tolerance
Example: PF1262 0.5 Ohm 1%
1
Power rating based on 25°C Flange Temperature
2
Power rating based on 25°C Ambient Temperature
3
Consult Factory for Higher or Lower Values
Specifi cation Value
Maximum Current 25A
Temperature Range -55°C to +155°C : PF1262
Dielectric Strength 2000 VAC
Max. Operating Voltage 500 V
Insulation Resistance >1000 Meg-Ohm
Environmental Performance R Test Conditions
Load Life ±1% + 0.05 25°C / 90 min ON / 30 min OFF / 1000 hr
Humidity Resistance ±1% + 0.05 40°C / 90-95% RH / DC 0.1W / 1000 hr
Temperature Cycle ±0.25% + 0.05 -55°C for 30 min / +155°C for 30 min / 1000 hr
Solder Heat ±0.1% + 0.05 +350°C / 3s
Vibration ±0.25% + 0.05
IEC60068-2-6
Type
Power Rating
Heatsink
1
Free Air
2
Thermal
Resistance
Resistance Range
3
Min Max
Tolerances
Temperature
Coeffi cients
PF1262 20W 1W 5.9K/W 0.01 51K
±1% ( R0.1Ω )
±5%
±50ppm/°C ( R10Ω )
±100ppm/°C ( 0.1≤ R < 10)
±250ppm/°C ( R < 0.1)
TO-126 Power Thin Film Resistors
Ordering Information
Riedon Inc. 300 Cypress Avenue Alhambra CA 91801 (626) 284-9901 (626) 284-1704
www.riedon.com
08/14
SPECIFICATIONS (continued)
Power Rating Notes -
The PF1260 Series Thin Film Resistors must be attached to a
suitable heatsink. The maximum internal resistor temperature is
155°C.
To specify an appropriate heatsink use the following formula :
R
θH
= T
MAX
- ( P x R
θR
) - T
A
P
Where: R
θH
= Thermal Resistance of Heatsink ( K/W )
R
θR
= Thermal Resistance of Resistor ( K/W )
T
MAX
= Maximum Temperature of Resistor
T
A
= Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
Mounting Notes -
The PF1260 Series Thin Film Resistors must be attached to
a suitable heatsink. Mount resistor using thermal grease to
a clean / fl at surface. Use a compression washer to provide
150 to 300 pounds ( 665 to 1330N ) of mounting force. Torque
mounting screw to 8 in-lbs ( 0.9 Nm ).
Back plate is isolated from both pins.
PF1262 Series
TO-126 Power Thin Film Resistors
-25 0 25 50 75 100 125 150 175
0
20
40
60
80
100
120
Power ( % )
Backplate Temperature (°C)
PF1262
Power Derating Curve

PF1262-0R02J2

Mfr. #:
Manufacturer:
Description:
RES 0.02 OHM 20W 5% TO126
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet