4
Latch Setup Time, t
S
(See Figure 4) 25 25 - - ns
Full 35 - - ns
Latch Hold Time, t
H
(See Figure 4) 25 0 - - ns
Full 0 - - ns
Latch Pulse Width, t
WPW
(See Figure 4) 25 15 - - ns
Full 25 - - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0, (See Figure 2) 25 - 0.3 1 pC
NO/NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
= V
COM
= 0V, (See Figure 8) 25 - 3 - pF
COM OFF Capacitance, C
OFF
f = 1MHz, V
NO
= V
COM
= 0V, (See Figure 8) 25 - 12 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
= V
COM
= 0V, (See Figure 8) 25 - 18 - pF
OFF Isolation R
L
= 50, C
L
= 15pF, f = 100kHz, V
NO
= 1V
RMS
,
(See Figures 5 and 7)
25 - 92 - dB
Crosstalk, (Note 8) 25 - 110 - dB
All Hostile Crosstalk, (Note 8) 25 - -105 - dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 2-6V
Positive Supply Current, I+ V
S
= 5.5V, V
LATCHH
, V
ADD
= 0V or V+,
Switch On or Off
25 -1 0.1 1 A
Full -1 - 1 A
Negative Supply Current, I- 25 -1 0.1 1 A
Full -1 - 1 A
NOTES:
3. V
IN
= logic voltage to configure the device in a given state.
4. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
5. R
ON
= R
ON
(MAX) - R
ON
(MIN).
6. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25
o
C.
8. Between any two switches.
Electrical Specifications + 12V Supply Test Conditions: V+ = +10.8V to +13.2V, GND = 0V, V
INH
= 4V, V
INL
= 0.8V (Note 3),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
(NOTE 4)
MIN TYP
(NOTE 4)
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 10.8V, I
COM
= 1.0mA, V
NO
= 9V, (See Figure 6) 25 - 37 45
Full - 55
R
ON
Matching Between Channels,
R
ON
V+ = 10.8V, I
COM
= 1.0mA, V
NO
= 9V, (Note 5) 25 - 1.2 2
Full - - 2
R
ON
Flatness, R
FLAT(ON)
V+ = 10.8V, I
COM
= 1.0mA, V
NO
= 3V, 6V, 9V, (Note 6) 25 - 5 7
Full - - 7
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 13.2V, V
COM
= 1V, 12V, V
NO
= 12V, 1V, (Note 7) 25 -0.1 0.002 0.1 nA
Full -2.5 - 2.5 nA
Electrical Specifications: 5V Supply Test Conditions: V
SUPPLY
= 4.5V to 5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 3),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
(NOTE 4)
MIN TYP
(NOTE 4)
MAX UNITS
ISL43841
