AON7407
Symbol Min Typ Max Units
BV
DSS
-20 V
V
DS
=-20V, V
GS
=0V -1
T
J
=55°C -5
I
GSS
±100 nA
V
GS(th)
Gate Threshold Voltage
-0.3 -0.55 -0.9 V
I
D(ON)
-100 A
7.6 9.5
T
J
=125°C 10.5 13.5
9.3 12.5 mΩ
11.4 18 mΩ
g
FS
72 S
V
SD
-0.52 -1 V
I
S
-35 A
C
iss
2795 3495 4195 pF
C
oss
365 528 690 pF
C
rss
255 425 595 pF
R
g
2.8 5.6 Ω
Q
g
35 44 53 nC
Q
gs
9 nC
Q
gd
11 nC
t
D(on)
18 ns
t
r
32 ns
t
D(off)
136 ns
t
f
59 ns
t
rr
26 33 40 ns
Q
rr
80 100 120 nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Body Diode Reverse Recovery Time
Drain-Source Breakdown Voltage
On state drain current
I
D
=-250µA, V
GS
=0V
V
GS
=-4.5V, V
DS
=-5V
V
GS
=-4.5V, I
D
=-14A
Reverse Transfer Capacitance
I
F
=-14A, dI/dt=500A/µs
V
GS
=0V, V
DS
=-10V, f=1MHz
SWITCHING PARAMETERS
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
I
DSS
µA
V
DS
=V
GS
,
I
D
=-250µA
V
DS
=0V, V
GS
= ±8V
Zero Gate Voltage Drain Current
Gate-Body leakage current
Forward Transconductance
Diode Forward Voltage
R
DS(ON)
Static Drain-Source On-Resistance
mΩ
I
S
=-1A,V
GS
=0V
V
DS
=-5V, I
D
=-14A
V
GS
=-1.8V, I
D
=-11A
V
GS
=-2.5V, I
D
=-13A
V
GS
=-4.5V, V
DS
=-10V,
R
L
=0.75Ω, R
GEN
=3Ω
Gate resistance
V
GS
=0V, V
DS
=0V, f=1MHz
Turn-Off Fall Time
Total Gate Charge
V
GS
=-4.5V, V
DS
=-10V, I
D
=-14A
Gate Source Charge
Gate Drain Charge
Body Diode Reverse Recovery Charge
I
F
=-14A, dI/dt=500A/µs
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
DYNAMIC PARAMETERS
Turn-On Rise Time
Turn-Off DelayTime
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The Power
dissipation P
DSM
is based on R
θJA
t ≤ 10s value and the maximum allowed junction temperature of 150°C. The value in any given application
depends on the user's specific board design.
B. The power dissipation P
D
is based on T
J(MAX)
=150°C, using junction-to-case thermal resistance, and is more useful in setting the upper dissipation
limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=150°C. Ratings are based on low frequency and duty cycles to keep initial T
J
=25°C.
D. The R
θJA
is the sum of the thermal impedance from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedance which is measured with the device mounted to a large heatsink, assuming a
maximum junction temperature of T
J(MAX)
=150°C. The SOA curve provides a single pulse ratin g.
G. The maximum current rating is package limited.
H. These tests are performed with the device mounted on 1 in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C.
Rev 0: June 2011 www.aosmd.com Page 2 of 6
