Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
8.3 Vdc - 14 Vdc Input 0.75 Vdc - 5.0 Vdc/3 A Output
Input Specifications (continued)
Parameter Min Typ Max Notes
Remote Off Input Current - 3 mA 6 mA
Input Reflected Ripple Current (pk-pk)
Vo=5.0 V
Vo=3.3 V
Vo=0.75 V
-
-
-
75 mA
50 mA
20 mA
120 mA
90 mA
35 mA
Input Reflected Ripple Current (rms)
Vo=5.0 V
Vo=3.3 V
Vo=0.75 V
-
-
-
20 mA
15 mA
5 mA
60 mA
30 mA
15 mA
Tested with two 100 uF/25 V tantalum
input capacitors & simulated source
impedance of 1 uH, 5 Hz to 20 MHz.
I
2
t Inrush Current Transient - 0.01 A
2
s0.02 A
2
s
Turn-on Voltage Threshold 7.6V 7.9 V 8.2 V
Turn-off Voltage Threshold 7.0V 7.8 V 8.1 V
Output Specifications
Parameter Min Typ Max Notes
Output Voltage Set Point -2% Vo,set - 2% Vo,set Vin=12 V, lo=lomax, full load
Output Voltage Set Point -2.5% Vo,set - 3.5% Vo,set
Over all operating input
voltages, resistive loads and
temperature conditions
Load Regulation 0.5% Vo,set 0.4% Vo,set 0.5% Vo,set Io=Iomin to Iomax
Line Regulation 0.4% Vo,set 0.3% Vo,set 0.4% Vo,set Vin=Vinmin to Vinmax
Regulation Over Temperature
(-40 °C to +85 °C)
- 0.5% Vo,set 0.8% Vo,set
Output Current 0 A - 3 A
Current Limit Threshold 5 A - 12 A
Short Circuit Surge Transient
- 0.15 A
2
s -
Ripple and Noise (pk-pk)
Vo=5.0 V
Vo=3.3 V
Vo=0.75 V
-
-
-
65 mV
45 mV
20 mV
100 mV
80 mV
35 mV
Ripple and Noise (rms)
Vo=5.0 V
Vo=3.3 V
Vo=0.75 V
-
-
-
20 mV
10 mV
5 mV
40 mV
25 mV
15 mV
Tested with 0-20 MHz, with
10 uF/10 V tantalum capacitor
and 1uF/10 V ceramic
capacitor at the output
Turn on Time - 5 mS 8 mS
Overshoot at Turn on - 0% 3%
Output Capacitance 0 uF - 1200 uF
Transient Response
50% ~ 100% Max Load - 200 mV 300 mV
Settling Time - 50 uS 80 uS
100% ~ 50% Max Load - 200 mV 300 mV
Settling Time
All
- 50 uS 80 uS
di/dt=2.5 A/uS; Vin=12 V; and
with 10 uF/10 V tantalum
capacitor and 1 uF/10 V
ceramic capacitor at the output
Note: All specifications are typical at nominal input (Vin=12 V), full load at 25 °C unless otherwise stated.