NB6L72M
http://onsemi.com
5
Table 5. DC CHARACTERISTICS, Multi-Level Inputs V
CC
= 2.375 V to 3.63 V, GND = 0 V, T
A
= -40°C to +85°C
Symbol
Characteristic Min Typ Max Unit
POWER SUPPLY CURRENT
I
CC
Power Supply Current (Inputs and Outputs Open) 60 80 105 mA
CML OUTPUTS (Notes 5 and 6)
V
OH
Output HIGH Voltage
V
CC
= 3.3 V
V
CC
= 2.5 V
V
CC
- 40
3260
2460
V
CC
- 10
3290
2490
V
CC
3300
2500
mV
V
OL
Output LOW Voltage
V
CC
= 3.3 V
V
CC
= 2.5 V
V
CC
- 500
2800
2000
V
CC
- 400
2900
2100
V
CC
- 300
3000
2200
mV
DIFFERENTIAL INPUT DRIVEN SINGLE-ENDED (see Figures 6 and 8)
V
th
Input Threshold Reference Voltage Range (Note 7) 1050 V
CC
- 150 mV
V
IH
Single-Ended Input HIGH Voltage V
th
+ 150 V
CC
mV
V
IL
Single-Ended Input LOW Voltage GND V
th
- 150 mV
V
ISE
Single-Ended Input Voltage Amplitude (V
IH
- V
IL
) 300 V
CC
- V
EE
mV
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (see Figures 7 and 9) (Note 8)
V
IHD
Differential Input HIGH Voltage 1200 V
CC
mV
V
ILD
Differential Input LOW Voltage GND V
CC
- 150 mV
V
ID
Differential Input Voltage Swing (Dn, Dn) (V
IHD
- V
ILD
) (Note 15) 150 V
CC
- V
EE
mV
V
CMR
Input Common Mode Range (Differential Configuration) (Note 9) 950 V
CC
– 75 mV
I
IH
Input HIGH Current Dn/Dn, (VTDn/VTDn Open) -150 +150
mA
I
IL
Input LOW Current Dn/Dn, (VTDn/VTDn Open) -150 +150
mA
SINGLE-ENDED LVCMOS/LVTTL CONTROL INPUTS
V
IH
Single-Ended Input HIGH Voltage 2000 V
CC
mV
V
IL
Single-Ended Input LOW Voltage GND 800 mV
I
IH
Input HIGH Current -150 +150
mA
I
IL
Input LOW Current -150 +150
mA
TERMINATION RESISTORS
R
TIN
Internal Input Termination Resistor 40 50 60
W
R
TOUT
Internal Output Termination Resistor 40 50 60
W
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. CML outputs loaded with 50 W to V
CC
for proper operation.
5. Input and output parameters vary 1:1 with V
CC
.
6. V
th
, V
IH
, V
IL,,
and V
ISE
parameters must be complied with simultaneously.
7. V
th
is applied to the complementary input when operating in single-ended mode.
8. V
IHD
, V
ILD,
V
ID
and V
CMR
parameters must be complied with simultaneously.
9. V
CMR
minimum varies 1:1 with GND, V
CMR
max varies 1:1 with V
CC
. The V
CMR
range is referenced to the most positive side of the differential
input signal.
