MP2030DQ-LF-Z

MP2030
3A Dual Supply
Very Low Dropout Linear Regulator
MP2030 Rev. 0.91 www.MonolithicPower.com 1
10/10/2011 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2011 MPS. All Rights Reserved.
The Future of Analog IC Technology
DESCRIPTION
The MP2030 is a very low dropout, dual supply
linear regulator. The use of two supplies allows
the BIAS to control an NMOS device. The
NMOS device supplies power to the load via
the IN. In this way the input supply can be just
above the desired output, yet still provide very
good regulation performance due to the higher
bias supply. The BIAS operates from a 2.5V to
5.5V input and regulates the output voltage to
as low as 0.9V, and as high as 3.8V.
The MP2030 can supply up to 3A of load
current with a typical dropout voltage of 150mV.
The BIAS runs the internal reference and drive
circuitry, while the output current comes directly
from the IN for high efficiency regulation.
The low bias current of 220uA makes the
MP2030 ideal for use in battery-powered
applications. The BIAS can be directly applied
from the battery while IN is powered from the
high efficiency buck regulator. This will reduce
the output noise and decoupling capacitor.
Other features of MP2030 include thermal
overload and current limit protection, power
good indicator, stability with ultra low ESR
ceramic capacitors as low as 1uF, and fast
transient response. The MP2030 is available in
10-pin QFN (3mm x 3mm), and in QFN (5mm x
5mm) packages.
FEATURES
Wide 1.1V to 5.5V Input Voltage Range
Stable with Very Small Ceramic Capacitors
150mV Dropout at 3A Output
2% Accurate Output Voltage
Adjustable Output Range of 0.9V to 3.8V
Low Noise: 80µV
RMS
(10Hz to 100kHz)
PSRR
o 32dB at 100kHz
Better Than 0.001%/mA Load Regulation
Stable With Low-ESR Output Capacitors
Low 220uA Ground Current
Internal Thermal Protection
Current Limit Protection
0.1µA Typical Quiescent Current at
Shutdown
Power Good Indicator
APPLICATIONS
Network, Telecom, Equipment: Routers
and Switches
Servers, Storage Equipment
Set-Top Box
Post Regulation for Switch Mode
Televisions
“MPS” and “The Future of Analog IC Technology” are Registered Trademarks of
Monolithic Power Systems, Inc.
TYPICAL APPLICATION
C6
10nF
U1
IN OUT
OUT
FB
EN
BP
IN
BIAS
PG
GND
MP2030
5
3
1
8
9
6
10
7
2
4
VIN
BIAS
PGOOD
GND
EN
C8
1nF
GND
VOUT
1.8V/3A
MP2030 – 3A VERY LOW DROPOUT LINEAR REGULATOR
MP2030 Rev. 0.91 www.MonolithicPower.com 2
10/10/2011 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2011 MPS. All Rights Reserved.
ORDERING INFORMATION
Part Number* Package Top Marking Free Air Temperature (T
A
)
MP2030DQ*
3x3 QFN10
7D
–40°C to +85°C
MP2030DU**
5x5 QFN32
M2030DU
–40°C to +85°C
* For Tape & Reel, add suffix –Z (eg. MP2030DQ–Z).
For RoHS compliant packaging, add suffix –LF (eg. MP2030DQ–LF–Z)
** For Tape & Reel, add suffix –Z (eg. MP2030DU–Z).
For RoHS compliant packaging, add suffix –LF (eg. MP2030DU–LF–Z)
PACKAGE REFERENCE
TOP VIEW
VIN
VIN
BIAS
PGOOD
GND
1
2
3
4
5
VOUT
VOUT
FB
EN
BYPASS
10
9
8
7
6
EXPOSED PAD
ON BACKSIDE
3x3 QFN10
ABSOLUTE MAXIMUM RATINGS
(1)
V
BIAS
, V
IN
to GND............................–0.3V to +6V
FB, EN, to GND ..............................–0.3V to 6V
V
OUT
...............................–0.3V to V
IN
+ 0.3 or 6V
PGOOD ..................... –0.3V to V
BIAS
+ 0.3 or 6V
BYPASS ......................-0.3V to V
BIAS
+0.3 or 6V
Junction Temperature...............................150°C
Lead Temperature ....................................260°C
Storage Temperature ............. –65°C to +150°C
Power Dissipation
T
A
=70°C (QFN10 3 x 3) ............................ 1.3W
T
A
=70°C (QFN32 5 x 5) ............................. 1.8W
TOP VIEW
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
N/C
VIN
VIN
VIN
VIN
BIAS
PGOOD
GND
N/C
VOUT
VOUT
VOUT
VOUT
FB
EN
BYPASS
N/C
N/C N/C N/C N/C N/C N/C N/C
N/C
N/C N/C N/C N/C N/C N/C N/C
910111213141516
32 31 30 29 28 27 26
25
EXPOSED PAD
ON BACKSIDE
5x5 QFN32
Recommended Operating Conditions
(2)
Input Voltage V
IN
............................. 1.1V to 5.5V
Input Voltage V
BIAS
.......................... 2.5V to 5.5V
Output Voltage................................ 0.9V to 3.6V
Load Current............................... 3.0A Maximum
Operating Junct. Temp. ...........–40°C to +125°C
Thermal Resistance
(3)
θ
JA
θ
JC
QFN10 3X3… ......................... 50……12 °C/W
QFN32 5X5… ......................... 36….…8 °C/W
Notes:
1) Exceeding these ratings may damage the device.
2) The device is not guaranteed to function outside of its
operating conditions.
3) Measured on JESD51-7, 4-layer PCB.
MP2030 – 3A VERY LOW DROPOUT LINEAR REGULATOR
MP2030 Rev. 0.91 www.MonolithicPower.com 3
10/10/2011 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2011 MPS. All Rights Reserved.
ELECTRICAL CHARACTERISTICS
V
IN
= 1.5V, V
BIAS
= 3.6V, V
OUT
= 1.2V, C
OUT
= 1µF, C
IN
= 0.1µF, T
A
= +25°C, unless otherwise noted.
Parameter Symbol Condition Min Typ Max Units
V
IN
Operating Voltage 1.1 5.5 V
V
BIAS
Operating Voltage 2.5 5.5 V
V
BIAS
Operating Current 220 μA
0.490 0.500 0.510
FB Regulation Voltage
–40°C T
A
+85°C
0.485 0.500 0.515
V
Dropout Voltage I
OUT
= 3A, V
BIAS
= 3.6V 150 mV
V
IN
Line Regulation
I
OUT
= 1mA,
V
IN
= 1.5 to 5V
V
BIAS
= 3.6V V
OUT
= 1.2V
1 mV
V
BIAS
Line Regulation
I
OUT
= 1mA,
V
BIAS
= 3.6V to 5.5V V
OUT
= 1.2V
V
IN
= 1.5V
2 mV
Load Regulation I
OUT
= 1mA to 1A 0.001 %/mA
PSRR
(V
IN
)
V
IN
> V
OUT
+ 0.5V, C
OUT
= 22μF,
V
IN
(AC) = 100mV, f = 100KHz
I
OUT
= 300mA
32 dB
Power Good Threshold 440 mV
Power Good Delay 160 μs
Soft Start BYPASS=open 550 μs
Power Good Voltage I
sink
=230μA 0.39 V
EN Input High Voltage 1.5 V
EN Input Low Voltage 0.8 V
EN Input Bias Current V
EN
= 1.2V –1 +1 μA
Thermal Protection 135
°C
Thermal Protection Hysteresis 15
°C

MP2030DQ-LF-Z

Mfr. #:
Manufacturer:
Monolithic Power Systems (MPS)
Description:
LDO Voltage Regulators 3A ultra-low dropout LDO Regulator
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet