78K0R/KG3 ターゲット・ボード
QB-78K0RKG3-TB ユーザーズ・マニュアル
ユーザーズ・マニュアル
R01UH0149XJ0200
Rev 2.00 2013.6.28
本製品は、ルネサス エレクトロニクス製のプログラミング機能付きオンチップ・デバッグ・エミュレータ QB-MINI2 を使用して、マイコンの動
作を試すためのターゲット・ボードです。
①78K0R/KG3 ターゲット・ボード(QB-78K0RKG3-TB)の特徴
●78K0R/KG3(μPD78F1166GF)搭載
●20MHz の発振子を搭載
●ユニバーサル・エリア(2.54mm ピッチ)を搭載
●フラッシュ・メモリ・プログラミング、オンチップ・デバッグに両対応(TOOL0,TOOL1 端子使用)
●マイコンの端子を周辺ボード・コネクタに配置した高拡張性
●鉛(Pb)フリー対応品
②78K0R/KG3 ターゲット・ボード(QB-78K0RKG3-TB)のハードウエア仕様
CPU μPD78F1166GF メイン・クロック動作周波数 20MHz(ボード上に搭載)
CN1,CN2: 周辺ボードコネクタ(2.54mm ピッチ) 50pin ソケット x2(パッドのみ)
FP1: 16pin コネクタ(QB-MINI2 接続用)
PowerLED: 赤 x1(LED3)
評価用 LED: 黄 x2(LED1 は P76,LED2 は P77 へ接続)
評価用 SW: SW1(INTP0 へ接続)
搭載部品
メイン・クロック(Y1): 20MHz 発振子(X1,X2 へ接続)
動作電圧 2.7V~5.5V
③寸法、部品配置など
1
15
QB-78K0RKG3-TB
SS-77045
評価用 LED
上:LED2
下:LED1
16pinコネクタ
CN1
CN2
CN2
CN1
71.12mm
55.88mm
FP1
45.72mm
50
49
2
1
LED3
VDD
GND
1
2
49
50
78K0R
/KG3
SW1
INTP0
LED2
LED1
P77
P76
メイン・クロック
Y1
P123,P124
ショートパッド
評価用 SW
Power LED
ユニバーサル
・エリア
AVREF1
EVDD
AVREF0
P121,P122ショートパッド
基板上のパターン について:パターンをカットすることで、その回路はオープンとなります。
再度接続させたい場合は半田ショートしてください。
P76,P77 を使用する場合は LED の左のショートパッドをパターンカットしてください。
P123/P124 はプルダウン抵抗に接続されています。これが問題になる場合はショートパッドをパターンカットしてください。
P121/P122 はデフォルトオープンになっています。20MHz で動作させる場合は半田ショートしてください。
回路図のパッドの表示 オープン:
ショート:
④使用上の注意
・本製品に関してのサポートはお受けしておりません。初期不良の場合に限り、交換いたします。
R01UH0149XJ0200 Rev.2.00 Page 1 of 2
2013.6.28
78K0R/KG3 Target board
QB-78K0RKG3-TB User’s Manual
User’s Manual
R01UH0149XJ0200
Rev 2.00 2013.6.28
The QB-78K0RKG3-TB is a target board used for evaluating microcontroller operations, using the QB-MINI2, the Renesas
Electronics on-chip debug emulator with programming function.
(1) 78K0R/KG3
target board (QB-78K0RKG3-TB) features
● Incorporates 78K0R/KG3 (μPD78F1166GF)
● A 20 MHz resonator is mounted
● Equipped with universal area (2.54 mm pitch)
● Supports both flash memory programming and on-chip debugging (using TOOL0/TOOL1 pins)
● Highly extendable; peripheral board connectors are equipped with microcontroller pins
● Lead-free (Pb-free) product
(2) 78K0R/KG3
target board (QB-78K0RKG3-TB) hardware specifications
CPU μPD78F1166GF Main clock operating frequency 20 MHz (mounted on board)
CN1, CN2: Peripheral board connectors (2.54 mm pitch), 50-pin socket 2 (pad only)
FP1: 16-pin connector (for QB-MINI2 connection)
Power LED: Red 1 (LED3)
Test LED: Yellow 2 (LED1 connected to P76, LED2 connected to P77)
Test SW: SW1 (connected to INTP0)
Embedded parts
Main clock (Y1): 20 MHz resonator (connected to X1 and X2)
Operating voltage 2.7 to 5.5 V
(3) Dimensions and parts layout
1
15
QB-78K0RKG3-TB
SS-77045
Test LED
upper:LED2
lower:LED1
16pin connector
CN1
CN2
CN2
CN1
71.12mm
55.88mm
FP1
45.72mm
50
49
2
1
LED3
VDD
GND
1
2
49
50
78K0R
/KG3
SW1
INTP0
LED2
LED1
P77
P76
Main Clock
Y1
Universal
area
Power LED
Test SW
P123,P124
Short Pad
AVREF0
EVDD
AVREF1
P121,P122 Short Pad
Pattern on the board:
Splitting this wiring leaves open the relevant circuit ( ).
To reconnect the circuit, short the circuit by soldering (
).
When using P76 and P77, cut off the short pad on the left side of LED.
P123/P124 is connected to pull down registers. If it is a problem, cut off the short pads.
P121 and P122 are open as default. Short the circuit P121 and P122 by soldering to operate
with 20MHz.
Showing of the pad on circuit diagram. open:
short:
(4) Notes on use
● Renesas Electronics will not provide any support for this board, but the board can be exchanged with a new product only when
it has an initial failure.
R01UH0149XJ0200 Rev.2.00 Page 1 of 2
2013.6.28