OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

PL-USB2-BLASTER

P1-P3P4-P6P7-P9P10-P12P13-P14
Symbol Parameter Conditions Min Max Unit
3.3-V low-level
output voltage
V
CC(TRGT)
= 3.6 V, I
OL
= 1 mA — 0.125 V
2.5-V low-level
output voltage
V
CC(TRGT)
= 2.625 V, I
OL
= 1 mA — 0.125 V
1.8-V low-level
output voltage
V
CC(TRGT)
= 1.89 V, I
OL
= 1 mA — 0.125 V
1.5-V low-level
output voltage
V
CC(TRGT)
= 1.57 V, I
OL
= 1 mA — 0.125 V
I
CC(TRGT)
Operating current
(No Load)
Typical I
CC(TRGT)
= 16 uA — 100 uA
Table 7. DC Operating Conditions for USB Download Cable Rev. C
Symbol Parameter Conditions Min Max Unit
V
IH
High-level input
voltage
V
CC(TRGT)
>= 2.0 V 2.0 — V
V
CC(TRGT)
< 2.0 V V
CC(TRGT)
— V
V
IL
Low-level input
voltage
V
CC(TRGT)
>= 2.0 V — 0.8 V
V
CC(TRGT)
< 2.0 V — 0 V
V
OH
5.0-V high-level
output voltage
V
CC(TRGT)
= 4.5 V, I
OH
= -10 mA 3.8 — V
3.3-V high-level
output voltage
V
CC(TRGT)
= 3.0 V, I
OH
= -8 mA 2.3 — V
2.5-V high-level
output voltage
V
CC(TRGT)
= 2.375 V, I
OH
= -6 mA 1.8 — V
1.8-V high-level
output voltage
V
CC(TRGT)
= 1.71 V, I
OH
= -4 mA 1.2 — V
V
OL
5.0-V high-level
output voltage
V
CC(TRGT)
= 5.5 V, I
OL
= 10 mA — 0.8
3.3-V high-level
output voltage
V
CC(TRGT)
= 3.6 V, I
OL
= 8 mA — 0.7
2.5-V high-level
output voltage
V
CC(TRGT)
= 2.625 V, I
OL
= 6 mA — 0.6
1.8-V high-level
output voltage
V
CC(TRGT)
= 1.89 V, I
OL
= 4 mA — 0.5
I
CC(TRGT)
Operating current
(No Load)
Typical I
CC(TRGT)
= 16 uA — 100 uA
2.5 Power Requirements
The USB Download Cable V
CC(TRGT)
pin must be connected to a specific voltage for the
device being programmed. Connect pull-up resistors to the same power supply as the
USB Download Cable V
CC(TRGT)
.
2 Specifications for USB Download Cable
Intel FPGA USB Download Cable User Guide
7
Table 8. V
CC(TRGT)
Power Requirements
Device Family Voltage Required
FPGAs
Stratix V, Stratix IV, and Stratix III
As specified by V
CCPGM
or V
CCPD
.
Stratix II, Stratix II GX, and Stratix GX
As specified by V
CCSEL
.
Arria 10
As specified by V
CCPGM
or V
CCIO
.
Arria V
As specified by V
CCPD
.
Arria II GX
As specified by V
CCPD
or V
CCIO
of Bank 8C
Arria GX
As specified by V
CCSEL
.
Cyclone V
As specified by V
CCPGM
or V
CCPD
.
Cyclone IV
As specified by V
CCA
or V
CCIO
.
Cyclone III
As specified by V
CCA
or V
CCIO
.
Max 10
As specified by V
CCIO
.
Configuration Devices
EPCS 3.3 V
EPCQ 3.3 V
EPCQ-L 1.8 V
2.6 RoHS Compliance
Table 9. Hazardous Substances and Concentration
A value of 0 indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold as specified by the SJ/T11363-2006 standard.
Part Name
Lead (Pb) Cadmium
(Cd)
Hexavalent
Chromium
(Cr6+)
Mercury
(Hg)
Polybromina
ted
Biphenyls
(PBB)
Polybromina
ted Diphenyl
Ethers
(PBB)
Electronic components 0 0 0 0 0 0
Populated circuit
board
0 0 0 0 0 0
Manufacturing process 0 0 0 0 0 0
Packing 0 0 0 0 0 0
2 Specifications for USB Download Cable
Intel FPGA USB Download Cable User Guide
8
3 Using the USB Download Cable
To start using the USB Download Cable, you must install the drivers on your system
and set up the hardware in the Quartus
®
Prime software. Intel recommends that you
use the latest version of the Quartus Prime software.
To program or configure the device, connect the host system to the device board using
the USB Download Cable and initiate the programming or configuration using the
Quartus Prime Programmer. You can also use the cable with the Quartus Prime
SignalTap
®
II Logic Analyzer for logic analysis.
3.1 Installing the USB Download Cable Driver on Windows
1.
Locate the USB Download Cable driver in \<Quartus Prime system
directory>\drivers\usb-blaster.
If the driver is not in your directory, download the driver from www.altera.com/
support/software/drivers.
2. Connect the USB Download Cable to your PC.
3. Open Device Manager. In the Other devices tab, select and right click USB-
Blaster. Then, click Update Driver Software.
4.
Click Browse. Browse to \<Quartus Prime system directory>\drivers
\usb-blaster and click Next.
The Windows security warning is displayed.
5. Click Install to begin installing the driver.
6. Click Finish when the driver is installed.
7. Restart your system.
Related Links
Cable and Adapter Drivers Information
3.2 Installing the USB Download Cable Driver on Linux
The Quartus Prime software uses the USB drivers (usbfs) provided by Red Hat Linux to
access the USB Download Cable. You need system administration (root) privileges to
configure the drivers. You must also change the permission on the ports before using
the USB Download Cable to program devices.
Related Links
Cable and Adapter Drivers Information
3 Using the USB Download Cable
©
2016 Intel Corporation. All rights reserved. Intel, the Intel logo, Altera, Arria, Cyclone, Enpirion, MAX,
Megacore, NIOS, Quartus and Stratix words and logos are trademarks of Intel Corporation in the US and/or
other countries. Other marks and brands may be claimed as the property of others. Intel warrants performance
of its FPGA and semiconductor products to current specifications in accordance with Intel's standard warranty,
but reserves the right to make changes to any products and services at any time without notice. Intel assumes
no responsibility or liability arising out of the application or use of any information, product, or service
described herein except as expressly agreed to in writing by Intel. Intel customers are advised to obtain the
latest version of device specifications before relying on any published information and before placing orders for
products or services.
ISO
9001:2008
Registered
P1-P3P4-P6P7-P9P10-P12P13-P14

PL-USB2-BLASTER

Mfr. #:
Buy PL-USB2-BLASTER
Manufacturer:
Intel / Altera
Description:
Programmer Accessories USB 2.0 Prog Cable FPGA CPLD Ser Conf
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet