2
FN6258.2
August 25, 2010
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only.
Absolute Maximum Ratings (T
A
= +25°C) Thermal Information
Supply Voltage from VSP to GND . . . . . . . . . . . . . . . . . . . . . . . . 6V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . V
S
+ +0.3V to GND -0.3V
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +125°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135°C
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . .6000V
Machine Model (Per EIAJ ED-4701 Method C-111). . . . . . . .300V
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +125°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135°C
Thermal Resistance (Typical, Note 1) θ
JA
(°C/W)
6 Ld SC-70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty..
1. θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications V
SP
= +5V, Z
RSC
= Z
LOAD
= 50Ω, T
A
= +25°C, 24Ω V
SP
to OUT, unless otherwise specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
Vsp Supply Voltage To operate below 5V, the 24Ω resistor to supply
should be reduced
3.0 5.5 V
Gt Small Signal Gain 1.0GHz 17 18.3 19.5 dB
1.5GHz 16.1 17.4 18.6 dB
2.0GHz 15.1 16.6 17.6 dB
P1dB Output Power at 1dB Compression 1.0GHz 16 17.7 19 dBm
2.0GHz 15.9 17.2 18.9 dBm
OIP3 Output Third Order Intercept Point 1.0GHz 30 dBm
2.0GHz 27 dBm
OIP2 Output Second Order Intercept Point Input tones at 1.0GHz and 1.1GHz,
at Input Power = -15dBm, Output tone 2.1GHz
44.2 dBm
BW 3dB Bandwidth 3dB below Gain @ 500MHz 2.4 GHz
IRL Input Return Loss 1.0GHz Z
RSC
= 75Ω, Z
LOAD
= 50Ω 23.5 dB
ORL Output Return Loss 1.0GHz Z
RSC
= 75Ω, Z
LOAD
= 50Ω 21.8 dB
RISOL Reverse Isolation 2.0GHz 22.4 dB
NF Noise Figure 2.0GHz 4.7 dB
ID Device Operating Current 56 63.5 71 mA
ISL55012