Philips Semiconductors Product specification
74ALVT162245
2.5V/3.3V 16-bit transceiver
with 30Ω termination resistors (3-State)
1998 Feb 13
6
DC ELECTRICAL CHARACTERISTICS (2.5V 0.2V RANGE)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS Temp = -40°C to +85°C UNIT
MIN TYP
1
MAX
V
IK
Input clamp voltage V
CC
= 2.3V; I
IK
= –18mA –0.85 –1.2 V
V
OH
High-level output voltage V
CC
= 2.3V; I
OH
= –8mA 1.7
V
OL
Low-level output voltage V
CC
= 2.3V; I
OL
= 12mA 0.6 0.7
V
CC
= 2.7V; V
I
= V
CC
or GND Control pins 0.1 ±1
p
V
CC
= 0 or 2.7V; V
I
= 5.5V 0.1 10
I
V
CC
= 2.7V; V
I
= V
CC
p
0.1 1
V
CC
= 2.7V; V
I
= 0
0.1 -5
I
OFF
Off current V
CC
= 0V; V
I
or V
O
= 0 to 4.5V 0.1 ±100 µA
Bus Hold current V
CC
= 2.3V; V
I
= 0.7V 90
HOLD
Data inputs
6
V
CC
= 2.3V; V
I
= 1.7V –75
I
EX
Current into an output in the
High state when V
O
> V
CC
V
O
= 5.5V; V
CC
= 2.3V 20 125 µA
I
PU/PD
Power up/down 3-State output
current
3
V
CC
≤ 1.2V; V
O
= 0.5V to V
CC
; V
I
= GND or V
CC
OE/OE = Don’t care
40 100 µA
I
CCH
V
CC
= 2.7V; Outputs High, V
I
= GND or V
CC,
I
O
= 0 0.04 0.1
I
CCL
Quiescent supply current V
CC
= 2.7V; Outputs Low, V
I
= GND or V
CC,
I
O
= 0 2.5 4.5 mA
I
CCZ
V
CC
= 2.7V; Outputs Disabled; V
I
= GND or V
CC,
I
O
= 0
5
0.04 0.1
∆I
CC
Additional supply current per
input pin
2
V
CC
= 2.3V to 2.7V; One input at V
CC
–0.6V,
Other inputs at V
CC
or GND
0.05 0.4 mA
NOTES:
1. All typical values are at V
CC
= 2.5V and T
amb
= 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than V
CC
or GND
3. This parameter is valid for any V
CC
between 0V and 1.2V with a transition time of up to 10msec. From V
CC
= 1.2V to V
CC
= 2.5V ± 0.2V a
transition time of 100µsec is permitted. This parameter is valid for T
amb
= 25°C only.
4. Unused pins at V
CC
or GND.
5. I
CCZ
is measured with outputs pulled up to V
CC
or pulled down to ground.
6. Not guaranteed.
AC CHARACTERISTICS (2.5V 0.2V RANGE)
GND = 0V; t
R
= t
F
= 2.5ns; C
L
= 50pF; R
L
= 500Ω; T
amb
= –40°C to +85°C.
LIMITS
SYMBOL PARAMETER WAVEFORM V
CC
= 2.5V 0.2V UNIT
MIN TYP
1
MAX
t
PLH
t
PHL
Propagation delay
nAx to nBx or nBx to nAx
1
1.5
1.5
2.9
2.4
5.3
4.7
ns
t
PZH
t
PZL
Output enable time
to High and Low level
2
1.5
1.5
4.3
3.1
6.3
4.6
ns
t
PHZ
t
PLZ
Output disable time
from High and Low Level
2
1.5
1.5
4.2
3.3
6.2
5.1
ns
NOTE:
1. All typical values are at V
CC
= 2.5V and T
amb
= 25°C.
