VS-30TPS16PbF, VS-30TPS16-M3
www.vishay.com
Vishay Semiconductors
Revision: 06-Feb-14
2
Document Number: 94387
For technical questions within your region: DiodesAmericas@vishay.com
, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum average on-state current I
T(AV)
T
C
= 95 °C, 180° conduction half sine wave 20
A
Maximum RMS on-state current I
RMS
30
Maximum peak, one-cycle,
non-repetitive surge current
I
TSM
10 ms sine pulse, rated V
RRM
applied 250
10 ms sine pulse, no voltage reapplied 300
Maximum I
2
t for fusing I
2
t
10 ms sine pulse, rated V
RRM
applied 310
A
2
s
10 ms sine pulse, no voltage reapplied 442
Maximum I
2
t for fusing I
2
t t = 0.1 to 10 ms, no voltage reapplied 4420 A
2
s
Maximum on-state voltage drop V
TM
20 A, T
J
= 25 °C 1.3 V
On-state slope resistance r
t
T
J
= 125 °C
12 m
Threshold voltage V
T(TO)
1.0 V
Maximum reverse and direct leakage current I
RM
/I
DM
T
J
= 25 °C
V
R
= Rated V
RRM
/V
DRM
0.5
mA
T
J
= 125 °C 10
Maximum holding current I
H
Anode supply = 6 V, resistive load, initial I
T
= 1 A, T
J
= 25 °C 150
Maximum latching current I
L
Anode supply = 6 V, resistive load, T
J
= 25 °C 200
Maximum rate of rise of off-state voltage dV/dt T
J
= T
J
maximum, linear to 80 % V
DRM
, R
g
-k = Open 500 V/µs
Maximum rate of rise of turned-on current dI/dt 150 A/µs
TRIGGERING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum peak gate power P
GM
8.0
W
Maximum average gate power P
G(AV)
2.0
Maximum peak positive gate current + I
GM
1.5 A
Maximum peak negative gate voltage - V
GM
10 V
Maximum required DC gate current to trigger I
GT
Anode supply = 6 V, resistive load, T
J
= - 10 °C 60
mAAnode supply = 6 V, resistive load, T
J
= 25 °C 45
Anode supply = 6 V, resistive load, T
J
= 125 °C 20
Maximum required DC gate
voltage to trigger
V
GT
Anode supply = 6 V, resistive load, T
J
= - 10 °C 2.5
V
Anode supply = 6 V, resistive load, T
J
= 25 °C 2.0
Anode supply = 6 V, resistive load, T
J
= 125 °C 1.0
Maximum DC gate voltage not to trigger V
GD
T
J
= 125 °C, V
DRM
= Rated value
0.25
Maximum DC gate current not to trigger I
GD
2.0 mA
SWITCHING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Typical turn-on time t
gt
T
J
= 25 °C 0.9
µsTypical reverse recovery time t
rr
T
J
= 125 °C
4
Typical turn-off time t
q
110
