CD4016BCMX Datasheet CD4016BCM, CD4016BCN, CD4016BCMX | P1-P3

November 1983

Revised March 2002

CD4016BC Quad Bilateral Switch

CD4016BC

Quad Bilateral Switch

General Description

The CD4016BC is a quad bilateral switch intended for the

transmission or multiplexing of analog or digital signals. It is

pin-for-pin compatible with CD4066BC.

Features

■ Wide supply voltage range: 3V to 15V

■ Wide range of digital and analog switching:

±7.5 V

PEAK

■ “ON” Resistance for 15V operation: 400Ω (typ)

■ Matched “ON” Resistance over 15V signal input:

∆R

ON

= 10Ω (typ)

■ High degree of linearity:

0.4% distortion (typ)

@ f

IS

= 1 kHz, V

IS

= 5 V

p-p

,

V

DD

−V

SS

= 10V, R

L

= 10 kΩ

■ Extremely low “OFF” switch leakage:

0.1 nA (typ.)

@ V

DD

− V

SS

= 10V

T

A

= 25°C

■ Extremely high control input impedance: 10

12

Ω (typ)

■ Low crosstalk between switches:

−50 dB (typ.)

@ f

IS

= 0.9 MHz, R

L

= 1 kΩ

■ Frequency response, switch “ON”: 40 MHz (typ)

Applications

• Analog signal switching/multiplexing

Signal gating

Squelch control

Chopper

Modulator/Demodulator

Commutating switch

• Digital signal switching/multiplexing

• CMOS logic implementation

• Analog-to-digital/digital-to-analog conversion

• Digital control of frequency, impedance, phase, and

analog-signal gain

Ordering Code:

Devices also available in Tape and Reel. Specify by appending the letter suffix “X” to the ordering code.

Connection Diagram Schematic Diagram

Order Number Package Number Package Description

CD4016BCM M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow

CD4016BCN N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide

www.fairchildsemi.com 2

CD4016BC

Absolute Maximum Ratings(Note 1)

(Note 2)

Recommended Operating

Conditions

(Note 2)

Note 1: “Absolute Maximum Ratings” are those values beyond which the

safety of the device cannot be guaranteed. They are not meant to imply

that the devices should be operated at these limits. The tables of “Recom-

mended Operating Conditions” and “Electrical Characteristics” provide con-

ditions for actual device operation.

Note 2: V

SS

= 0V unless otherwise specified.

DC Electrical Characteristics (Note 2)

Note 3: If the switch input is held at V

DD

, V

IHC

is the control input level that will cause the switch output to meet the standard “B” series V

OH

and I

OH

output

levels. If the analog switch input is connected to V

SS

, V

IHC

is the control input level — which allows the switch to sink standard “B” series |I

OH

|, HIGH level

current, and still maintain a V

OL

≤ “B” series. These currents are shown in Table 1.

V

DD

Supply Voltage −0.5V to +18V

V

IN

Input Voltage −0.5V to V

DD

+ 0.5V

T

S

Storage Temperature Range −65°C to + 150°C

Power Dissipation (P

D

)

Dual-In-Line 700 mW

Small Outline 500 mW

Lead Temperature

(Soldering, 10 seconds) 260

°C

V

DD

Supply Voltage 3V to 15V

V

IN

Input Voltage 0V to V

DD

T

A

Operating Temperature Range −55°C to +125°C

Symbol Parameter Conditions

−55°C25°C +125°C

Units

Min Max Min Typ Max Min Max

I

DD

Quiescent Device V

DD

= 5V, V

IN

= V

DD

or V

SS

0.25 0.01 0.25 7.5 µA

Current V

DD

= 10V, V

IN

= V

DD

or V

SS

0.5 0.01 0.5 15 µA

V

DD

= 15V, V

IN

= V

DD

or V

SS

1.0 0.01 1.0 30 µA

Signal Inputs and Outputs

R

ON

“ON” Resistance R

L

= 10kΩ to (V

DD

− V

SS

)/2

V

C

= V

DD

, V

IS

= V

SS

or V

DD

V

DD

= 10V 600 250 660 960 Ω

V

DD

= 15V 360 200 400 600 Ω

R

L

= 10kΩ to (V

DD

− V

SS

)/2

V

C

= V

DD

V

DD

= 10V, V

IS

= 4.75 to 5.25V 1870 850 2000 2600 Ω

V

DD

= 15V, V

IS

= 7.25 to 7.75V 775 400 850 1230 Ω

∆R

ON

∆“ON” Resistance R

L

= 10kΩ to (V

DD

− V

SS

)/2

Between any 2 of V

C

= V

DD

, V

IS

= V

SS

to V

DD

4 Switches V

DD

= 10V 15 Ω

(In Same Package) V

DD

= 15V 10 Ω

I

IS

Input or Output V

C

= 0, V

DD

= 15V ±50 ±0.1 ±50 ±500 nA

Leakage V

IS

= 0V or 15V,

Switch “OFF” V

OS

= 15V or 0V

Control Inputs

V

ILC

LOW Level Input V

IS

= V

SS

and V

DD

Voltage V

OS

= V

DD

and V

SS

I

IS

= ±10 µA

V

DD

= 5V 0.9 0.7 0.5 V

V

DD

= 10V 0.9 0.7 0.5 V

V

DD

= 15V 0.9 0.7 0.5 V

V

IHC

HIGH Level Input V

DD

= 5V 3.5 3.5 3.5 V

Voltage V

DD

= 10V 7.0 7.0 7.0 V

V

DD

= 15V 11.0 11.0 11.0 V

(Note 3) and Table 1

I

IN

Input Current V

CC

− V

SS

= 15V ±0.1 ±10

−5

±0.1 ±1.0 µA

V

DD

≥ V

IS

≥ V

SS

V

DD

≥ V

C

≥ V

SS

3 www.fairchildsemi.com

CD4016BC

AC Electrical Characteristics (Note 4)

T

A

= 25°C, t

r

= t

f

= 20 ns and V

SS

= 0V unless otherwise specified

Note 4: AC Parameters are guaranteed by DC correlated testing.

Note 5: These devices should not be connected to circuits with the power “ON”.

Note 6: In all cases, there is approximately 5 pF of probe and jig capacitance on the output; however, this capacitance is included in C

L

wherever it is

specified.

Note 7: V

IS

is the voltage at the in/out pin and V

OS

is the voltage at the out/in pin. V

C

is the voltage at the control input.

Symbol Parameter Conditions Min Typ Max Units

t

PHL

, t

PLH

Propagation Delay Time V

C

= V

DD

, C

L

= 50 pF, (Figure 1)

Signal Input to Signal Output R

L

= 200k

V

DD

= 5V 58 100 ns

V

DD

= 10V 27 50 ns

V

DD

= 15V 20 40 ns

t

PZH

, t

PZL

Propagation Delay Time R

L

= 1.0 kΩ, C

L

= 50 pF, (Figure 2, Figure 3)

Control Input to Signal V

DD

= 5V 20 50 ns

Output HIGH Impedance to V

DD

= 10V 18 40 ns

Logical Level V

DD

= 15V 17 35 ns

t

PHZ

, t

PLZ

Propagation Delay Time R

L

= 1.0 kΩ, C

L

= 50 pF, (Figure 2, Figure 3)

Control Input to Signal V

DD

= 5V 15 40 ns

Output Logical Level to V

DD

= 10V 11 25 ns

HIGH Impedance V

DD

= 15V 10 22 ns

Sine Wave Distortion V

C

= V

DD

= 5V, V

SS

= −50.4%

R

L

= 10 kΩ, V

IS

= 5 V

P-P

, f = 1 kHz,

(Figure 4)

Frequency Response — Switch V

C

= V

DD

= 5V, V

SS

= −5V, 40 MHz

“ON” (Frequency at −3 dB) R

L

= 1 kΩ, V

IS

= 5 V

P-P

,

20 Log

10

V

OS

/V

OS

(1 kHz) −dB,

(Figure 4)

Feedthrough — Switch “OFF” V

DD

= 5V, V

C

= V

SS

= −5V, 1.25 MHz

(Frequency at −50 dB) R

L

= 1 kΩ, V

IS

= 5 V

P-P

,

20 Log

10

(V

OS

/V

IS

) = −50 dB,

(Figure 4)

Crosstalk Between Any Two V

DD

= V

C(A)

= 5V; V

SS

= V

C(B)

= −5V, 0.9 MHz

Switches (Frequency at −50 dB) R

L

= 1 kΩV

IS(A)

= 5 V

P-P

,

20 Log

10

(V

OS(B)

/V

OS(A)

) = −50 dB,

(Figure 5)

Crosstalk; Control Input to V

DD

= 10V, R

L

= 10 kΩ 150 mV

P-P

Signal Output R

IN

= 1 kΩ, V

CC

= 10V Square Wave,

C

L

= 50 pF (Figure 6)

Maximum Control Input R

L

= 1 kΩ, C

L

= 50 pF, (Figure 7)

V

OS(f)

= ½ V

OS

(1 kHz)

V

DD

= 5V 6.5 MHz

V

DD

= 10V 8.0 MHz

V

DD

= 15V 9.0 MHz

C

IS

Signal Input Capacitance 4pF

C

OS

Signal Output Capacitance V

DD

= 10V 4 pF

C

IOS

Feedthrough Capacitance V

C

= 0V 0.2 pF

C

IN

Control Input Capacitance 57.5 pF

CD4016BCMX

CD4016BCMX

Products related to this Datasheet