TDS LOCTITE GC 3W, January-2016
Reflow:
● Reflow has been assessed using a typical convection reflow
oven.
● Optimal aerobic reflow can be achieved by ramping to a peak
temperature of 225 to 250ºC at 0.8 to 1.5ºC/second and with a
soak above the reflow temperature (217ºC) for 20 to 50 seconds.
● Example profiles that have shown good performance- for reflow
and subsequent cleaning- are presented below. Reflow soldering
can also be carried out in a nitrogen atmosphere.
Cleaning:
● The post-soldering residues of LOCTITE GC 3W solder paste
must be removed by cleaning.
● Cleaning can be performed using spray in air/ spray under
immersion or ultrasonic cleaning methods.
● The post-soldering residues are designed to be removed from
assemblies in an aqueous cleaner without the use of rinse aids
and/or saponifiers, typically using water at 40 to 60ºC with
deionized water for the final rinse.
RELIABILITY PROPERTIES
Flux Properties:
LOCTITE GC 3W contains a stable water-washable resin system and
slow evaporating solvents
Test Specification Results
Flux Corrosion J-STD004B (2.6.15C) Pass
Copper Mirror J-STD004B (2.3.32D) Pass
(cleaned)
Surface Insulation
Resistance (SIR)
J-STD004B (2.6.3.7) Pass
(cleaned)
J-STD004B (2.6.3.3) Pass
(cleaned)
Electromigration (ECM) J-STD004B (2.6.14.1) Pass
Flux Activity Classification J-STD004B ORM0
PACKAGING
LOCTITE GC 3W is available in 500 gram jars and 600 grams Semco
cartridge .
Storage:
Optimal storage: 0 to 25ºC ± 1.5°C (32 to 77ºF ± 1.5ºF)
Storage information may be indicated on the product container
labelling. Material removed from containers may be contaminated
during use. Do not return products to the original container. Henkel
Corporation cannot assume responsibility for product that has been
contaminated or stored under conditions other than those previously
indicated. If additional information is required, please contact your
local Technical Service Center or Customer Service Representative.
Shelf Life:
Provided LOCTITE GC 3W is stored tighly sealed in the original
container at 0 to 25°C ± 1.5°C (32 to 77ºF ± 1.5ºF), a minimum shelf
life of 180 days can be expected.
DATA RANGES
The data contained herein may be reported as a typical value and/or a
range. Values are based on actual test data and are verified on a
periodic basis.
GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Not for Product Specifications
The technical information contained herein is intended for reference
only. Please contact Henkel Technologies Technical Service for
assistance and recommendations on specifications for this product.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
Americas Europe Asia
+1.888.943.6535 +32.1457.5611 +86.21.3898.4800
For the most direct access to local sales and technical support visit:www.henkel.com/electronics