R0E000010ACB20 Datasheet R0E000010ACB20 | P1-P3

User's Manual

R20UT2740EJ0100 Rev.1.00 Page 1 of 8

Dec 01, 2013

CN2

CN1

SW1

SW3SW5

SW4

RL78 Other

I/OO/HizO O RH850Other

RL78 Other

R0E000010ACB20

Isolator for the E1 Emulator of RH850 and RL78

1. Preface

The R0E000010ACB20 is an isolator for the E1 emulator of RH850 and RL78.

This product is used for a debugging environment where there is a GND gap

between the user system and emulator system.

Package Components

Before using this product, check if your R0E000010ACB20 contains all of

these items.

Table 1.1 Package Components

Item

Qty.

R0E000010ACB20 (Isolator for the E1 emulator)

R0E000010ACB20 User's Manual (English) (This manual)

R0E000010ACB20 User's Manual (Japanese)

Note: Please handle this product as precision equipment for transportation.

Important

Caution on Isolation Voltage:

This product is intended to isolate a small and electrically safe GND gap between the user system and

emulator system. In any case isolation voltage must be maintained within SELV limits i.e. less than

42.4VAC, or 60VDC.

The isolator must never be used as an element of a safety isolation system. The part could be expected to

function correctly at higher voltage across the isolation barrier; but then the circuitry on both sides of the

barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must

form a barrier between these circuits and any user-accessible circuitry according to safety standard

requirements.

Caution to Be Taken for Disposal:

Penalties may be applicable for incorrect disposal of this waste, in accordance with your national

legislation.

European Union regulatory notices:

The WEEE (Waste Electrical and Electronic Equipment) regulations put responsibilities on producers for

the collection and recycling or disposal of electrical and electronic waste. Return of WEEE under these

regulations is applicable in the European Union only. This equipment (including all accessories) is not

intended for household use. After use the equipment cannot be disposed of as household waste, and the

WEEE must be treated, recycled and disposed of in an environmentally sound manner. Renesas

Electronics Europe GmbH can take back end of life equipment, register for this service at

“

http://www.renesas.eu/weee”.

Cautions to Be Taken for Handling the Isolator:

• Take full care not to touch any parts or cause short circuits on this product.

• Protect this product from excessive physical shock.

• Do not modify this product. Modifying the product will void your warranty.

Cautions for Use Temperature:

The isolator is to be used in an environment with a maximum ambient temperature of 35°C.

Care should be taken that this temperature is not exceeded.

R20UT2740EJ0100

Rev.

1.00

Dec 01, 2013

CAUTION

R0E000010ACB20 User's Manual

R20UT2740EJ0100 Rev.1.00 Page 2 of 8

Dec 01, 2013

Cautions to Be Taken for Connecting the Isolator:

• Always switch OFF the power before connecting or disconnecting this product.

• This product has some switches. Make settings depending on debugging interface you use.

Before changing settings power off this product and other connected devices.

• To connect this product to the user system align the #1 pin of the connector to the right position.

• To connect this product to the emulator align the #1 pin of the connector to the right position.

Cautions to Be Taken for Power Supply When Connecting:

• This product needs the power supply from both user system and E1 emulator.

• Do not change the voltage of the user system after turning on the power.

• When an attempt to connect the emulator debugger to the user system has failed, turn off the user

system and then unplug and plug the USB cable of the emulator before trying again.

Cautions to Be Taken for Power Supply When Disconnecting:

•

Turn off the power supply of the user system promptly when you disconnect the user system from the

emulator debugger. If the power supply of a user system continues being ON, a user program will carry

out a reset start. Moreover, you may fail to reconnect the emulator debugger to the user system.

• When an attempt to reconnect to the user system has failed, turn off the user system and then unplug

and plug the USB cable of the emulator before trying again.

European Union regulatory notices

This product complies with the following EU Directive.

Environmental Compliance and Certification:

• Waste Electrical and Electronic Equipment (WEEE) Directive 2012/19/EC

CAUTION

R0E000010ACB20 User's Manual

R20UT2740EJ0100 Rev.1.00 Page 3 of 8

Dec 01, 2013

2. Specifications

Table 2.1 Product Specifications

Item

Specification

Remark

Supported Emulator E1 emulator

Power

supply

User

system

side

Supply from the user system (UVCC)

Voltage: 3.0 V to 5.5 V

Supply from the user system (UVCC)

needs to be 100 mA (max).

emulator

side

Supply from the emulator’s power supply facility

Voltage: 3.3 V or 5.0 V

Acceptable GND gap

voltage

less than 42.4VAC, or 60VDC

Applicable MCU

Families

RH850

Family

RL78 Family

Isolator's switch settings vary

depending on the target MCU you

use.

See 4.6 Switch Settings for Each

MCU for switch setting.

Device for isolation ACSL-6420-00TE (Avago Technologies US Inc.)

IL261-3E

(NVE Corporation)

LED

indication

LED1: Illuminated when power is supplied from

the emulator

LED2: Illuminated when power is supplied from

the user system

This isolator is only usable when both

LEDs are illuminated.

Operating temperature

5 to 35°C (no condensation)

Storage temperature

-10 to 60°C (no condensation)

3. Notes on Usage

Note on Power-Supply Voltage:

When you use an emulator with this isolator connected, power-supply voltage of the MCU on your

system should be between 3.0 V and 5.5 V. Power-supply voltage less than 3.0 V is not supported

Notes on Using This Product with RH850 in LPD1pin mode:

(1) When using this product in LPD1pin mode, it is necessary to start up in 1wireUART by the Renesas

Flash Programmer first, following the procedures below.

1) Set the switches to 1wireUART referring to Section 4.1 of this manual.

2) Connect this product to the emulator and the user system referring to Section 4.2.

3) Turn on them referring to Section 4.3.

4) Start the Renesas Flash Programmer.

5) Choose [Microcontroller] menu -> [Set Option Bytes] command.

6) Choose [Microcontroller] menu -> [Set Project], and open [Project Settings] dialog

box. Choose

[Other Settings] tab and set the value of OPBT0 to LPD1pin mode. (For details see the user's

manual of the microcontroller.) Click [OK] and close [Project Settings] dialog box.

7) Click the start button on the main window and rewrite option bytes.

8) Exit the Renesas Flash Programmer.

9) Shut down the power supply referring to Section 4.4.

(2)

Notes on Starting up the CubeSuite+.

Be sure to set [Set OPJTAG in LPD connection before connecting] to [No]. If [Yes] is selected, the

debug tool starts up the microcontroller in serial programming mode, and the CubeSuite+ does not

start up.

(3)

Notes on Exiting the CubeSuite+

Set [Set OPJTAG in JTAG connection before disconnecting] to [No]. If [Yes] is selected, it is

necessary to repeat the procedure (1) described above next time the CubeSuite+ is started up.

Note on LPD data output (LPDO) with RH850 in LPD4pin mode:

When you use an emulator with this isolator connected, do not make terminal processing (pull-up or

pull-down) of LPD data output (LPDO) on your system.

P1-P3 P4-P6 P7-P8

R0E000010ACB20

Mfr. #:

Buy R0E000010ACB20

Manufacturer:

Renesas Electronics

Description:

Sockets & Adapters Isolator for E1 Emulator for RL78

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

R0E000010ACB20