WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
℃
CONSTANT CURRENT REGION
Note.4
CLG-150-12 A
A : IP65 rated. Output voltage and constant current level can be adjusted through internal
potentiometer.
Blank : IP67 rated. Cable for I/O connection.
B : IP67 rated. Constant current level adjustable through output cable.
C : Terminal block for I/O connection. Output voltage and constant current level can be adjusted through internal
potentiometer.
THD< 20% when output loading 75% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧
TOTAL HARMONIC DISTORTION
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC
SPECIFICATION
MODEL CLG-150-12 CLG-150-15 CLG-150-20 CLG-150-24 CLG-150-30 CLG-150-36 CLG-150-48
DC VOLTAGE
RATED CURRENT
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
Note.6
CURRENT ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.5
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
SAFETY STANDARDS
Note.7
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT (Typ.)
Note.4
OVER VOLTAGE
OVER TEMPERATURE
12V
9 ~12V
15V
11.25 ~ 15V
20V
15 ~ 20V
24V
18 ~ 24V
30V
22.5 ~ 30V
36V
27 ~ 36V
48V
36 ~ 48V
11A 9.5A 7.5A 6.3A
5A
4.2A 3.2A
132W 142.5W 150W 151.2W 150W 151.2W 153.6W
150mVp-p 150mVp-p
13 ~ 17V
150mVp-p
17 ~ 22V
150mVp-p
22 ~ 27V
150mVp-p
26 ~ 32V
150mVp-p
31 ~ 41V
200mVp-p
40 ~ 56V
±2.0%
5.5 ~ 11A
±2.0%
4.75 ~ 9.5A
±2.0%
3.75 ~ 7.5A
±1.0%
3.15 ~ 6.3A
±1.0%
2.5 ~ 5A
±1.0%
2.1 ~ 4.2A
±1.0%
1.6 ~ 3.2A
9 ~ 13V
Can be adjusted by internal
potentiometer A type and C type only
±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5%
±1.0% ±1.0% ±1.0% ±0.5% ±0.5% ±0.5% ±0.5%
3000ms, 80ms/115VAC 500ms, 80ms/230VAC at full load
50ms / 230VAC 16ms / 115VAC at full load
90 ~ 295VAC 127 ~ 417VDC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
88% 88% 90% 90% 91% 91% 91%
13.5 ~ 17V 18 ~ 23V 23 ~ 28V 28 ~ 34V 33 ~ 39V 42 ~ 50V 59 ~ 70V
2A / 115VAC 1A / 230VAC 0.68A / 277VAC
COLD START 65A(twidth=595 s measured at 50% Ipeak) at 230VAC
<1mA / 240VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV
), EAC TP TC 020
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH
℃
±℃ ℃
0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08, UL1012, CAN/CSA-C22.2 No. 107.1-01, UL879, CSA C22.2 No.207-M89, EN61347-1, EN61347-2-13
independent(except for CLG-150 C type),UL60950-1, TUV EN60950-1,GB19510.1,GB19510.14(for Blank & A type only),
303.7K hrs min. MIL-HDBK-217F (25 )℃
222.2*68*38.8mm (L*W*H)(CLG-150-Blank/A/B) 229*68*38.8mm (L*W*H)(CLG-150-C)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4.
Please refer to "DRIVING METHODS OF LED MODULE".
5. Derating may be needed under low input voltages. Please check the for more details.static characteristics
6. A type and C type only.
7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.
8
. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
9. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
1.0Kg; 12pcs/13Kg/0.58CUFT(CLG-150-Blank/A/B) 1Kg; 12pcs/13Kg/0.96CUFT(CLG-150-C)
Protection type : Shut down and latch off o/p voltage, re-power on to recover
150W Single Output Switching Power Supply
Universal AC input / Full range (up to 295VAC)
Built-in active PFC function
High efficiency up to 91%
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP65 / IP67 design for indoor or outdoor installations
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
3 years warranty
■
Features :
CLG-150 series
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, re-power on to recover
-30 ~ +70℃ (Refer to "Derating Curve")
110
SELV
IP65 IP67
SHORT CIRCUIT
Hiccup mode, recovers automatically after fault condition is removed
Compliance to EN55015, EN55032 Class B, EN61000-3-2 Class C ( 75% load) ; EN61000-3-3,GB17743 and GB17625.1, EAC TP TC 020≧
EMC IMMUNITY
EMC EMISSION
μ
File Name:CLG-150-SPEC 2018-01-08
S
&
E
( for BLANK&A type only)
IP65 or IP67, J61347-1, J61347-2-13(except for CLG-150 C type) EAC TP TC 004 approved
,
Bauar
Sicherheit
egel gema
t gepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os
