5
FN8037.7
June 10, 2010
Absolute Maximum Ratings Thermal Information
V
CC
to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3V to -7V
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14V
Input Voltages
T
IN
, FORCEOFF, FORCEON, EN, SHDN . . . . . . . . . -0.3V to 6V
R
IN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25V
Output Voltages
T
OUT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±13.2V
R
OUT
, INVALID. . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V
CC
+0.3V
Short Circuit Duration
T
OUT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
ESD Rating . . . . . . . . . . . . See “ESD PERFORMANCE” on page 7
Thermal Resistance (Typical, Notes 1, 2)
θ
JA
(°C/W) θ
JC
(°C/W)
32 Ld QFN Package. . . . . . . . . . . . . . . 32 2.0
Maximum Storage Temperature Range. . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
ISL4241EIR, ISL4243EIR . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
1. θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379, and Tech Brief TB389.
2. For θ
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Test Conditions: V
CC
= 3V to 5.5V, C
1
to C
4
= 0.1µF; Unless Otherwise Specified.
Typicals are at T
A
= +25°C
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Note 4) TYP
MAX
(Note 4) UNITS
DC CHARACTERISTICS
Operating Voltage Range Full 2.7 - 5.5 V
Supply Current, Automatic
Power-down
All R
IN
Open, FORCEON = GND, FORCEOFF = V
CC
(ISL4243E Only)
25 - 3 300 nA
Full - 50 300 nA
Supply Current, Power-down All R
IN
Open, FORCEOFF = SHDN = GND 25 - 3 300 nA
Full - 50 300 nA
Supply Current,
Automatic Power-down Disabled
All Outputs Unloaded,
FORCEON = FORCEOFF
= SHDN = V
CC
, V
CC
= 3.0V
25 - 0.3 1.0 mA
Full - 0.3 1.5 mA
LOGIC AND TRANSMITTER INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low T
IN
, FORCEON, FORCEOFF, EN, SHDN Full - - 0.8 V
Input Logic Threshold High T
IN
, FORCEON, FORCEOFF, EN, SHDN, V
CC
= 3.6V Full 2.0 - - V
Input Leakage Current T
IN
, FORCEON, FORCEOFF, EN, SHDN Full - ±0.01 ±1.0 µA
Output Leakage Current FORCEOFF
= GND (ISL4243E) or EN = V
CC
(ISL4241E) Full - ±0.05 ±10 µA
Transmitter Input Hysteresis 25 - 0.5 - V
Output Voltage Low I
OUT
= 1.6mA Full - - 0.4 V
Output Voltage High I
OUT
= -1.0mA Full V
CC
- 0.6 V
CC
- 0.1 - V
AUTOMATIC POWER-DOWN (ISL4243E Only, FORCEON = GND, FORCEOFF = V
CC
)
Receiver Input Thresholds to
Enable Transmitters
ISL4243E Powers Up (see Figure 7) Full -2.7 - 2.7 V
Receiver Input Thresholds to
Disable Transmitters
ISL4243E Powers Down (see Figure7) Full -0.3 - 0.3 V
INVALID
Output Voltage Low I
OUT
= 1.6mA Full - - 0.4 V
INVALID Output Voltage High I
OUT
= -1.0mA Full V
CC
- 0.6 - - V
Receiver Threshold to Transmitters
Enabled Delay (t
WU
)
Full - 20 100 µs
ISL4241E, ISL4243E
